Simple 9 steps of 2014 2015 Toyota Highlander Radio installation

The Toyota Highlander is a pretty good choice for most of us, some of you might be owners of it. If you are fans of Toyota Highlander, you must want to upgrade the Toyota Highlander Radio in order to have great fun with it. Most of you have no idea how to do this, and you will find the car factory for help. If you want to save some money, or enjoy the fun of DIY. Here are some simple steps for how to upgrade the radio of Toyota Highlander.

This is the image of Seicane Toyota Highlander Radio after installation. Do you think it’s awesome?

 

2014 2015 Toyota Highlander Radio after installation

2014 2015 Toyota Highlander Radio after installation

 

2014 2015 Toyota Highlander radio installation

(1)Begin your installation by removing the negative cable from the battery. Then return to the inside of the Toyota.

(2) Place the trim panel tool removal’s blade between the main dash panel and the trim panel surrounding the stereo and climate vents. Pry the panel from the dashboard and set it aside.

2014 2015 Toyota Highlander Radio installation step 1

2014 2015 Toyota Highlander Radio installation step 1

(3) Remove the three screws on either side of the Highlander’s stereo bracket with the Phillips-head screwdriver.

2014 2015 Toyota Highlander Radio installation step 2

2014 2015 Toyota Highlander Radio installation step 2

(4)Slide the stereo assembly from the Toyota’s dashboard stereo dock. Remove the three screws on the bracket to free the stereo from the housing. Slide the radio from the bracket.

2014 2015 Toyota Highlander Radio installation step 3

2014 2015 Toyota Highlander Radio installation step 3

(5)Unplug the stereo wiring connectors from the rear panel of the radio. Unplug the antenna cable from the back of the factory radio to complete the removal.

2014 2015 Toyota Highlander Radio installation step 4

2014 2015 Toyota Highlander Radio installation step 4

With these steps above, we can remove the Toyota Highlander Radio easily. After few minutes rest, we can install the new radio immediately.

(6) Make antennas and cables connected step by step as installation instructions show,and you should be very careful when you are doing this for it will affect whole procedure.

2014 2015 Toyota Highlander Radio installation step 5

2014 2015 Toyota Highlander Radio installation step 5

(7) Connected the new radio to your Toyota Highlander, you should check whether your connections are correct, the new unit is in right position,and you’d better have a tidy for the cables.

2014 2015 Toyota Highlander Radio installation step 6

2014 2015 Toyota Highlander Radio installation step 6

(8)Check whether the unit is working without problem.

(9)If everything is OK, firm six removed screws that are put aside,then make trim panel back on your new unit.

 

So what? If you don’t know which unit is better. Click here and you’ll find a wonderful unit:

http://www.seicane.com/10-2-inch-2014-2015-toyota-highlander-android-capacitive-touch-screen-radio-gps-navigation-system-with-bluetooth-tpms-dvr-obd-ii-rear-camera-aux-usb-sd-3g-wifi-steering-wheel-control-video-s082698

 

This unit hasQuad-core Android 4.2.2 operation system and 10.2 inch HD 1024*600 multi-touch screen with smooth operation, you can use high speed 3G&WiFi internet. You can download any applications in the android market for access to games, Skype, MSN, YouTube and so on. You can also use 3D navigation maps. Why don’t you get it now?

 

Wish this blog can help you when you want to upgrade your Toyota Highlander Radio.Enjoy  your car life every day.

2013 2014 Toyota Corolla Radio removal and installation with bluetooth DVD navigation system

As we all know, 2013 2014 Toyota Coralla is a pretty good choice for us. Some of you may be the fans of Toyota Coralla. Frankly, its original radio has few functions. If you want to watch HD video, make phone call or listen to music via bluetooth, use the navigation function. You should remove the original radio and install a new aftermarket radio instead. You might have no idea how to upgrade the original radio. Don’t worry, I’ll share some professional experience with you.

This image is the Seicane Toyota Corolla Radio after installation. If you have the same dashboard with it, you can follow the steps below.

2013 2014 Toyota Corolla after installation

2013 2014 Toyota Corolla after installation

 

Before the original radio removal, I’d like to share a good unit with you:

http://www.seicane.com/10-2-inch-2013-2014-toyota-corolla-android-gps-navigation-system-radio-capacitive-touch-screen-tpms-dvr-obd-ii-rear-camera-aux-usb-sd-3g-wifi-steering-wheel-control-hd-1080p-video-bluetooth-s082697

 

If you don’t know which unit is better, this one can be a good choice for you. It has intelligent pure android 4.2.2 operation system and 10.2 inch HD 1024*600 multi-touch screen and supports dual-screen display for the highest resolution of 2048*1536.

You can perform Google search on the road with quick search box, play online games, watch videos, download online data and check emails by connecting to any WiFi hotspot in range or 3g internet, download any applications in the android market for access to games, Skype, MSN, YouTube, twitter, E-Book, Gmail etc. And it is your perfect road companion.

 

2013 2014 Toyota Corolla Radio removal

1·First remove the negative cable from the battery.

2·Then return to the inside of the Toyota Coralla, pry off the vent panel with a plastic tool and pull it out.

2013 2014 Toyota Corolla Radio removal step 1

2013 2014 Toyota Corolla Radio removal step 1

3·Set the vent panel aside and pry down the trim panel as the picture shows, then disconnect one side harness of the trim panel.

2013 2014 Toyota Corolla Radio removal step 2

2013 2014 Toyota Corolla Radio removal step 2

4·You can see two 10mm bolts in the position as the picture shows, remove them. And do the same in left side.

2013 2014 Toyota Corolla Radio removal step 3

2013 2014 Toyota Corolla Radio removal step 3

5·Pull out the radio slowly and watch out the harnesses behind it.

2013 2014 Toyota Corolla Radio removal step 4

2013 2014 Toyota Corolla Radio removal step 4

6·Finally disconnect harnesses behind the original radio.

2013 2014 Toyota Corolla Radio removal step 5

2013 2014 Toyota Corolla Radio removal step 5

 

2013 2014 Toyota Corolla Radio installation

1·Make antennas and cables connected step by step as installation instructions show, and you should be very careful when you are doing this for it will affect whole procedure.

2·Connect the new Toyota Corolla Radio to your Toyota Corolla, you should check your connections, the new unit’s position, and you’d better have a tidy for the cables.

3·Check whether the unit is working properly.

4·If everything is OK, firm four removed bolts that are put aside, then make trim panel back on your new unit.

 

 

New car life with Toyota Corolla Radio is waiting for you. What are you waiting for?

14 steps to install a 2008 2009 2010 Toyota Prado Radio

If you have a Toyota Prado of 2008-2010, you need to know removal guide for 2008-2010 Toyota Prado Radio car stereo.Many people invite the professional workers when they install the head unit, but most people do it by themselves. Let’s have a look at the new unit after installation,stereo radio of 2008-2010 Toyota Prado first.

2010-2013 Toyota PRADO Radio after installation

2008-2010 Toyota PRADO Radio after installation

If you are not satisfied with your car’s recent radio, you can take the following advice as references.In fact,all the car DVD players are substantially identical but with minor differences. Therefore knowing how to remove 2010-2013 Toyota Prado Radio means that you can install car dvd player by yourself.Before discussing the installation, I will give you some advices about safety first.

When we are using the car DVD player, safety is the most important thing.Please do not stare at car DVD while driving, as it can disturb your attention.In addition, do not splash liquid on the unit for getting high playing quality.

The following are the removal steps for car’s head unit.

1.Take out the two blots that distributed on both sides of handbrake

2010-2013 Toyota PRADO Radio installation step 1

2008-2010 Toyota PRADO Radio installation step 1

2.Remove screws by your hand

2010-2013 Toyota PRADO Radio installation step 2

2008-2010 Toyota PRADO Radio installation step 2

3.After the bolts are removed,take out the left and right loosed dashboard

2010-2013 Toyota PRADO Radio installation step 3

2008-2010 Toyota PRADO Radio installation step 3

4.Disconnect the cable between them

2010-2013 Toyota PRADO Radio installation step 4

2008-2010 Toyota PRADO Radio installation step 4

5.Get out the screw by using your hand

2010-2013 Toyota PRADO Radio installation step 5

2008-2010 Toyota PRADO Radio installation step 5

6.Remove five screws as the picture show

2010-2013 Toyota PRADO Radio installation step 6

2008-2010 Toyota PRADO Radio installation step 6

7.Pull off the CD player

2010-2013 Toyota PRADO Radio installation step 7

2008-2010 Toyota PRADO Radio installation step 7

8.Disconnect the cables between them Gently

2010-2013 Toyota PRADO Radio installation step 8

2008-2010 Toyota PRADO Radio installation step 8

9.Connect the cables on the new head unit as the user manual shows and place them well.

10.Put the new head unit into the dash.

11.Turn on the new head unit and have a comprehensive check if it works well.

12.Install 4 screws back to their original position.

13.Check whether the unit is working without problem.

14.If everything is OK, make trim panel back on your new Seicane radio.

There are some details to mind during the following steps: you should slide the unit into the dash then connect the negative cable to the original wiring harness.Please remember that the wires should be connected correctly and the same to battery installation.

After your installation of Toyota Prado Radio turn on the new unit and operate it as the user instruction said.Check out all the functions in the unit and see whether everything works well or not. If it doesn’t, check the wires connections again or contact the technicians from the dealer for help.

Through the detailed description,I hold that you have mainly grasped how to remove original CD player of the car.For more information,please visit:

http://www.seicane.com/9-inch-aftermarket-android-touch-screen-gps-navigation-system-for-2008-2009-2010-toyota-prado-support-bluetooth-radio-tpms-dvr-obd-ii-rear-camera-aux-headrest-monitor-control-usb-sd-hd-1080p-video-3g-wifi-s082691

If you still have any problem on it,ask someone who works in this field for help.You will get a pleasant installation journey and you will find how convinent and perfect when the GPS Navigation System comes in your car.

2000 2001-2006 Toyota Corolla EX Radio installation

Here is the picture of Seicane 2000-2006 Toyota Corolla EX Radio after installation.

2000-2006 TOYOTA COROLLA EX Radio after installation

2000-2006 TOYOTA COROLLA EX Radio after installation

This Android 4.4.4 GPS Radio Car Audio System is ideal for upgrading your car’s factor radio of 2000 2001 2002 2003 2004 2005 2006 TOYOTA COROLLA EX. It has many advanced features, such as built-in gps navigation, Bluetooth, FM/AM radio, USB connection, and so on. A backup camera is also supported to provide assistance when you are reversing. Easy to install, this headunit is just plug and play. To check the compatibility of the unit with your car, please send a picture of your dashboard and the year and the model of your car to sales@seicane.com.

If you have the same dashboard with the picture shows, you can follow the instructions below.

 

Precautions before installation:

1.Before you begin any work, remember to disconnect negative power cable to avoid danger

2.Please turn off your car series include the radio unit and park your car well.

3.Before connecting, please make sure the ignition is off to avoid short circuit and connect the yellow and res cable at last.

 

2000-2006 Toyota Corolla EX Radio installation

1)First remove two trim panels at each side of center console and set it aside.

2000-2006 TOYOTA COROLLA EX Radio installation step 1

2000-2006 TOYOTA COROLLA EX Radio installation step 1

2)Remove the top panel and set it aside.

2000-2006 TOYOTA COROLLA EX Radio installation step 2

2000-2006 TOYOTA COROLLA EX Radio installation step 2

3)Remove 4 screws holding the unit with a Phillips screwdriver.

2000-2006 TOYOTA COROLLA EX Radio installation step 3

2000-2006 TOYOTA COROLLA EX Radio installation step 3

4)Gently take out the panel on the radio interface.

2000-2006 TOYOTA COROLLA EX Radio installation step 4

2000-2006 TOYOTA COROLLA EX Radio installation step 4

5)Then take out the radio and disconnect cables at back of it.

2000-2006 TOYOTA COROLLA EX Radio installation step 5

2000-2006 TOYOTA COROLLA EX Radio installation step 5

6)Connect the cables on the new head unit as the user manual shows and place them well.

7)Put the new head unit into the dash.

8)Turn on the new head unit and have a comprehensive check if it works well.

9)Install 4 screws back to their original position.

10)Check whether the unit is working without problem.

11)If everything is OK, make trim panel back on your new Seicane radio.

 

By the way, you should make sure whether the aftermarket radio fits your car before installation, and here is a good aftermarket radio of Seicane which fits Toyota Corolla EX well:

http://www.seicane.com/seicane-s126002-2000-2006-toyota-corolla-ex-android-4-4-4-gps-radio-car-audio-system-with-800-480-touch-screen-3g-wifi-dvd-player-bluetooth-obd2-mirror-link-steering-wheel-control-backup-camera-1080p

 

This Seicane Toyota Corolla EX Radio can be a good choice for you. It has intelligent pure android 4.4.4 operation system and 6.2 inch HD 800*480 multi-touch screen.

This in dash car DVD player features a useful and latest GPS system and the advanced bluetooth technology for easy wireless pairing with enabled devices to make or receive hands-free calls and enjoy streaming music. The ability of USB and an SD card slot are also provided for you for more portable devices to let you have an enjoyable experience while driving. The installation is quite easy and it is just plug and play. No wire needs to be modified or cut for the simple installation.

So, have a good time with your new Toyota Corolla EX Radio!

How to upgrade 2012 Toyota CAMRY Radio with 3D map mirror link airplay

Look at this image, owners of 2012 Toyota CAMRY might found it is familiar with your car. Yes, this is the center console of 2012 Toyota CAMRY. Although the original Toyota CAMRY Radio has many functions. Some of you may want to upgrade it for better functions and gain your entertainment. Today I will tell you how to upgrade your radio with 3D map mirror link airplay.

 

2012 Toyota CAMRY dashboard

2012 Toyota CAMRY dashboard

2012 Toyota CAMRY Radio installation

1)Unclip and remove the A/C vent.

2012 Toyota CAMRY Radio installation step 1

2012 Toyota CAMRY Radio installation step 1

2)Unsnap clock and leave hanging on top of dash.

2012 Toyota CAMRY Radio installation step 2

2012 Toyota CAMRY Radio installation step 2

3)Unclip and remove trim panel from each side of the pocket below the radio/climate control assembly.

2012 Toyota CAMRY Radio installation step 3

2012 Toyota CAMRY Radio installation step 3

4)Unscrew shifter knob counter clockwise.

2012 Toyota CAMRY Radio installation step 4

2012 Toyota CAMRY Radio installation step 4

5)Unclip shifter then use shift key override lever to pull shifter down, this makes it easier to remove the panel. unplug the connector(Have e-brake on).

2012 Toyota CAMRY Radio installation step 5

2012 Toyota CAMRY Radio installation step 5

6)Remove two screws lower dash panel.

2012 Toyota CAMRY Radio installation step 6

2012 Toyota CAMRY Radio installation step 6

7)Remove two 10mm bolts from arm rest.

2012 Toyota CAMRY Radio installation step 7

2012 Toyota CAMRY Radio installation step 7

8)Remove clip fitting and remove center console.

2012 Toyota CAMRY Radio installation step 8

2012 Toyota CAMRY Radio installation step 8

9)Remove two screws below the radio.

2012 Toyota CAMRY Radio installation step 9

2012 Toyota CAMRY Radio installation step 9

10)Remove pocket and unplug connectors.

2012 Toyota CAMRY Radio installation step 10

2012 Toyota CAMRY Radio installation step 10

11)Remove four 10mm bolts holding stereo in.

2012 Toyota CAMRY Radio installation step 11

2012 Toyota CAMRY Radio installation step 11

12)Remove stereo and unplug connectors.

2012 Toyota CAMRY Radio installation step 12

2012 Toyota CAMRY Radio installation step 12

13)Make antennas and cables connected step by step as installation instructions show, and you should be very careful when you are doing this for it will affect whole procedure.

14)Connect the new radio to your Toyota CAMRY, you should check whether your connections are correct, the new unit is in right position, and you’d better have a tidy for the cables.

15)Check whether the new unit is working without problem.

16)If there is no problem, firm removed screws and bolts that are put aside, then make trim panel back on your new unit.

 

Some of you guys might be troubled by choosing a right aftermarket Toyota CAMRY Radio.By the way, if you are looking for aftermarket radio for your Toyota CAMRY. I’d like to introduce a good one to you:

http://www.seicane.com/8-inch-android-head-unit-gps-navigation-system-for-2012-toyota-camry-with-dvd-player-bluetooth-mirror-link-radio-capacitive-multi-touch-screen-obd-dvr-rear-view-camera-tv-3g-wifi-usb-sd-ipod-s168016

 

If you don’t know which aftermarket radio is better, this unit can be a good choice for you. It has intelligent pure android 4.4.4 operation system and 8 inch HD 1024*600 multi-touch screen.With exquisite and user-friendly user interface, you can set any of your favorite application icons as shortcut on the main menu and set the position of the icons according to your preference.

 

Good luck! Hope you can install the new Toyota CAMRY Radio by yourself.

Specific installation insrtuctions for 2012 2013 Toyota Camry audio system with 3D navigation IPod

You may find that more and more car owners would more likely to install a dvd player by themselves.Does it mean they are all professional for it?I don’t think so for they should have searched right installation guide for Toyota Camry audio system and do according to it.

Today I will show you Specific installation insrtuctions for 2012 2013 Toyota Camry audio system with 3D navigation IPod and you will also have the ability to achieve this goal.

Car radio stereo audio system with BT music IPod of 2012 2013 Toyota Camry

Car radio stereo audio system with BT music IPod of 2012 2013 Toyota Camry

This fact also shows that demands for entertaining life is becoming very large and necessary.But how can we ensure that this one that above image show is just the one we need?Don’t worry,if you find the trim panels of the factory one and new one are almost same,then it is.So you will seek a stereo which can match your car first if you are going to upgrade your car audio system.

Precautions before installation:

1.Please check out the appearance and all functions of the car to make sure that original system is all right before installing the unit

2.Please do not shorten or extened the GPS antenna,for it will arise antenna problem

3.Notice that do not let the GPS antenna winding the steering wheel and shift lever,it can be dangerous

2012 2013 Toyota Camry radio removal and aftermarket audio installation:

1.Gently lever the below trim panel

Gently lever the below trim panel

Gently lever the below trim panel

2.Remove these two screws with a screwdriver as the picture show

Remove these two screws with a screwdriver

Remove these two screws with a screwdriver

3.Remove two screws that beside the white ones

Remove two screws that beside the white ones

Remove two screws that beside the white ones

4.Then you can gently pry the upper dashboard

gently pry the upper dashboard

gently pry the upper dashboard

5.Take  CD player out softly  and disconnect all the cables behind it

Take  CD player out softly

Take CD player out softly

disconnect all the cables behind it

disconnect all the cables behind it

6.CD player after removal

CD radio after removal

CD radio after removal

7.After the removal procedure,connect the cables of new unit to the right places,or you can take instructions as reference to finish this work,or ask someone who knows well to help you

8.Make upper dashboard and fasten four screws back to the unit and make the below dashboard to its original position

Whole process for Toyota Camry audio stereo head unit installation is over here,some of you may still have some doubts about this new unit,then you can visit some websites to gather the exact information,for example:http://www.seicane.com/8-inch-2012-2013-toyota-camry-aurion-eu-au-version-autoradio-dvd-player-tv-tuner-bluetooth-radio-rds-3g-wifi-pop-aux-backup-camera-hd-1080p-mp3-steering-wheel-control-c131.

Precautions when you operate the new unit:

1.Please do not use strong chemicals, cleaners, strong detergent to wipe the head unitr

3.Please use the touch screen pen or your finger to gently operate the unit,without using any other sharp objects, if not it will damage the screen.

3.Please keep the original display well when the staff is dismounting the original radio in order to use the original screw again

 

 

How to install 2007-2013 Toyota Land Cruiser 200 series aftermarket navigation system with radio 3G WIFI

Before we start talk about how to install 2007-2013 Toyota Land Cruiser 200 series aftermarket navigation system with radio 3G WIFI, I would like to let you to see next video and have a general understanding of it first.

Most of you may have the willing to equip your car with the stereo in the video which is very practical.But you should make sure that whether this unit can be installed in your car before at first.

You will make it clear with the help of next picture by comparing the trim panel.And then I will show you detailed installation steps for 2007-2013 Toyota Land Cruiser 200 series navigation system.

New unit after installation,navigation dvd with HD touch screen radio tuner of 2007-2013 Toyota Land Cruiser 200 series

New unit after installation,navigation dvd with HD touch screen radio tuner of 2007-2013 Toyota Land Cruiser 200 series

 

Please have a careful look at your trim panel of the original radio and check it whether looks alike this one’s,or you can ask someone who are professional to help you make this judgement.Finding a suitable car stereo is the basis for your installation.

When you have decided to install the more convenient one,you can take the following steps as references.Honestly speaking,all car radios are largely identical but with minor differences.Therefore knowing how to install car audio systems means that you can install a dvd player by yourself.

I have some advices about safety for you before talking about the installation.

Precautions for safety:

When we are using new car dvd radio, remember that safety is the most important.Please do not stare at or even use the stereo while driving, for it will disperse your attention.

When meeting high humidity atmosphere,for example,raining days, it may not work normally as the humidity may gather on screen. In addition, do not sprinkle any liquid on the unit to maintain high playing quality.The following part is about the removal steps for car’s head unit.

2007-2013 Toyota Land Cruiser head unit removal and installation:

1.Remove the two blots off  both sides of handbrake

Remove the two blots off  both sides of handbrake

Remove the two blots off both sides of handbrake

2.Remove screws with your hand

Remove screws with your hand

Remove screws with your hand

 

3.Remove left and right loosed dashboard after the bolts are taken off

Remove left and right loosed dashboard after the bolts are taken off

Remove left and right loosed dashboard after the bolts are taken off

4.Make the cable between them disconnected

Make the cable between them disconnected

Make the cable between them disconnected

5.Use your hand to take out the screw

Use your hand to take out the screw

Use your hand to take out the screw

6.Get five screws out as the picture show

Get the first screw out

Get the first screw out

Get the second and third screw out

Get the second and third screw out

Get the fourth and fifth screw out

Get the fourth and fifth screw out

7.Remove CD player from the unit

Remove CD player from the unit

Remove CD player from the unit

8.Gently unplugged the cables behind the player

Gently unplugged the cables behind the player

Gently unplugged the cables behind the player

As for the installation,after you have totally removed factory stereo,connect antennas of new unit to right positions,include cables and connectors.You can do it according to the installation instructions from the dealer.

After that, slip the unit into the dash then plug the negative cable to the original wiring harness as the guide show.If you want to know more information about this car dvd,you can visit some websites for help :http://www.seicane.com/9-inch-car-gps-radio-mount-for-2007-2013-toyota-land-cruiser-200-series-with-bluetooth-music-tv-tuner-cd-dvd-player-aux-3g-wifi-dvr-steering-wheel-control-pop-hd-1080p-c182.

Please mind that all wires should be correctly connected and the same to battery installation.After all these,turn on new radio and operate it with a touch screen pen.

Check out all functions of the unit to see whether your installation process is right. If it doesn’t, check the wires connection again or contact with technicians from the dealer for solutions.

 

 

 

Specific upgrade instructions for 2012 2013 Toyota Yaris radio stereo with audio system

Head unit after upgrade,radio GPS dvd player with navigation system of 2012 2013 Toyota Yaris

Head unit after upgrade,radio GPS dvd player with navigation system of 2012 2013 Toyota Yaris

This is one of the stereos which can be installed in Toyota Yaris of 2012 2013.From this image we can find that the appearance and functions which are showed on touch screen have all been changed,and it seems to be very wonderful to drive a car with a this kind of stereo.

People become more likely to seek entertaining things from everything which is possible.For working for a long period of time make us feel tired and want to enjoy ourselves well.Most people choose to have a travel and see beautiful scenery to free ourselves,and it will be better if we can have entertaining time when we are in the car.

If your audio system of 2012 2013 Toyota Yaris is still the factory one which operated by control buttons,then you can take the stereo upgrade into account.

It won’t be complex to get this object or even need to buy another car with advanced stereo,what you need to know is specific upgrade instructions for 2012 2013 Toyota Yaris radio stereo with audio system.

Don’t worry,it’s not difficult to reach this goal.First of all,you need to choose one suitable stereo for your car and then carefully read the following installation instructions.

Before installation,you can prepare some tools which may be useful,such as a lever or other pry tool and screwdriver,and you’d better ask someone beside you,so that he can make your work more smoothly.

2012 2013 Toyota Yaris original radio removal and new radio installation:

1.Remove trim panel of the radio

Remove trim panel of the radio

Remove trim panel of the radio

2.Take four mounting screws out

Take four mounting screws out

Take four mounting screws out

3.Gently remove the original radio

Gently remove the original radio

Gently remove the original radio

4.Make these four screws out

Make these four screws out

Make these four screws out

5.Take your hot new unit out

Take your hot new unit out

Take your hot new unit out

6.Do a test for QA

Do a test for QA

Do a test for QA

7.Take the transport screws  out

Take the transport screws  out

Take the transport screws out

8.Make your accessories plugged in

Make your accessories plugged in

Make your accessories plugged in

9.Take panels out to install reversing cam

Take panels out to install reversing cam

Take panels out to install reversing cam

10.Have a check for the camera prior to drilling

Have a check for the camera prior to drilling

Have a check for the camera prior to drilling

11.Fix screws that were taken out off the original radio

Fix screws that were taken out off the original radio

Fix screws that were taken out off the original radio

12.Install car other parts back to their original place

Install car other parts back to their original place

Install car other parts back to their original place

With the help of so detailed steps for Toyota Yaris radio replacement,I think most of you should have known the main jobs about upgrade affairs.

One thing will become not that difficult when you are sure or make up your mind to finish it,because when we have confidence and perseverance,things will become easier.So you will also do it well when there are these things in your heart.

And it’s usual that we account some situations which stops us going on,then you need to think about if you have done something wrong to the machine,or you can also visit next website to see whether your problem will be solved: http://www.seicane.com/2012-2013-toyota-yaris-gps-radio-sound-system-hd-touch-screen-cd-dvd-player-tv-tuner-bluetooth-aux-dvr-1080p-backup-camera-3g-wifi-ipod-iphone-steering-wheel-control-c146.There are a lot of detailed information that can be applied for you.

Hope you will soon enjoy nice entertaining time during driving and have a wonderful journey with your family or friends.

 

Upgrade steps for 2008 2009 2010 2011 Toyota Auris radio stereo sound system

New unit after installation,aftermarket autoradio stereo with sat nav system of 2008 2009 2010 2011 Toyota Auris.

New unit after installation,aftermarket autoradio stereo with sat nav system of 2008 2009 2010 2011 Toyota Auris

New unit after installation,aftermarket autoradio stereo with sat nav system of 2008 2009 2010 2011 Toyota Auris

Do you have a Toyota Auris for 2008 2009 2010 2011 and is your car stereo looks like this one?I guess most of you haven’t upgraded it for taking it as a complex thing.But in fact it’s not if you can find right upgraded steps for 2008 2009 2010 2011 Toyota Auris radio stereo sound system.

From the front picture,we can find that this new unit is different from original ones on its outside appearance and functions.Many people choose to replace factory stereo with a new one just for these changes.With rapid development of technology,people can also enjoy its labor work very quickly.

If you think that you are not very familiar with this unit,I advice you to visit following website which has more detailed information for it: http://www.seicane.com/double-din-sat-nav-speaker-upgrade-for-2008-2009-2010-2011-toyota-auris-with-hd-touch-screen-radio-rds-cd-dvd-player-tv-tuner-3g-wifi-aux-ipod-steering-wheel-control-c028.

Searching information about car dvd installation include reading articles which will show you specific steps to achieve it,so it’s right for you to have a look at it,no matter what kind of condition you are in,it will benefit your life more or less.

There are about 7 steps to accomplish Toyota Auris radio upgrade,and this process is mainly about removal steps.Because if you finished removal affairs it means that you have finished most of the installation.The removal generally can be divided into four parts,including remove trim panel,fasten screws,remove dashboard and take out the CD player.

2008 2009 2010 2011 Toyota Auris car stereo removal and installation:

1.Pry and release side panels from higher center with a panel removal tool

Pry and release side panels from higher center with a panel removal tool

Pry and release side panels from higher center with a panel removal tool

If you feel a little difficult,you can open up the left side console to achieve it

pry left side panel to help remove whold side panel

pry left side panel to help remove whold side panel

2.Take four screws out which distributed two on each side where the consoles were removed

Take four screws out which distributed two on each side where the consoles were removed

Take four screws out which distributed two on each side where the consoles were removed

3.You can gently take the dashboard out but also easily after four screws are taken down

 gently take the dashboard out but also easily after four screws are taken down

gently take the dashboard out but also easily after four screws are taken down

4.Then take out factory cd radio

 take out factory cd radio

take out factory cd radio

5.Gently disconnect all wiring one by one

Gently disconnect all wiring one by one

Gently disconnect all wiring one by one

6.Make connection on the cables between new unit and wiring of the car, then install it into the space right for it

7.Put the dashboard in original place and firm screws  that were set aside

It won’t take you much time to finish the installation of Toyota Auris nav system.Please be gentle to those things which are taken down by you,such as panels and you also set the screws at a visible place for easy to find.

If you hold that the aftermarket autoradio seems to be not very suitable for your car,you need to find more stereos and make a comparison,maybe http://www.seicane.com can be a not bad choice for you.Because sometime we know if this dvd radio is just the one I want when I see it at first sight.

I believe that your life especially when you are on a journey will be more colorful with a such car dvd player,and the gps nav system is one of the most popular functions.But before you enjoyed all these,keep your safety in mind when you are upgrading your car radio.

Warm tips:

The features of new head unit are good indeed,but do not let them instead of your attention or vigor,or it can be very dangerous.You can enjoy the beautiful music or sound when you are busy driving.

 

 

How to mount 2013 Toyota RAV4 aftermarket navigation system

New dvd radio after upgrade,autoradio with navigation system of 2013 Toyota RAV4

New dvd radio after upgrade,autoradio with navigation system of 2013 Toyota RAV4

Many things are upgrading at a surprising speed with faster and faster development of technology.This is just where the market is,because human begins need more advanced products,they are seeking for this kind of life style.Then how about your 2013 Toyota RAV4 car radio update?I will show you how to mount 2013 Toyota RAV4 aftermarket navigation system in this article.

This above picture is a suitable one which can match your Toyota RAV4,do you feel familiar with it for you have seen a similar one when you are going car market.Yes,this is the aftermarket car dvd with touch screen and bluetooth music.

Many of you are thinking about the upgrading affair but don’t know what to do with the car radio.Don’t worry,you’ll see specific installation steps for Toyota RAV4 radio in latter part.But please remember to remove the negative power cable from the battery before you begin your installation as the next picture shows.

2013 Toyota RAV4 cd player removal:

1.Use an automotive tool remove the upper dashboard trim panel,set the panel aside once removed

Use an automotive tool remove the upper dashboard trim panel,set the panel aside once removed

Use an automotive tool remove the upper dashboard trim panel,set the panel aside once removed

2.Prize the air conditioning vents gently which are on the left and right-hand sides of the factory touch screen unit away from the dashboard

prize the air conditioning vent gently on the right-hand sides of the factory touch careen unit away from the dashboard

prize the air conditioning vent gently on the right-hand sides of the factory touch careen unit away from the dashboard

prize the air conditioning vent gently on the left-hand side of the factory touch careen unit away from the dashboard

prize the air conditioning vent gently on the left-hand side of the factory touch careen unit away from the dashboard

3.Prize the clock display gently and hazard lamp panel away from the trim panel and set it to the side

Prize the clock display gently and hazard lamp panel away from the trim panel and set it to the side

Prize the clock display gently and hazard lamp panel away from the trim panel and set it to the side

4.Take four retaining screws attaching the factory touch screen unit to the dashboard out

Take four retaining screws attaching the factory touch screen unit to the dashboard out

Take four retaining screws attaching the factory touch screen unit to the dashboard out

5.Softly remove the touch screen unit  from the panel and lean it forward to gain access to the wiring harnesses on the reverse side

Softly remove the touch screen unit  from the panel and lean it forward to gain access to the wiring harnesses on the reverse side

Softly remove the touch screen unit from the panel and lean it forward to gain access to the wiring harnesses on the reverse side

6.Unplug the touch screen by pulling off the individual harnesses

Unplug the touch screen by pulling off the individual harnesses

Unplug the touch screen by pulling off the individual harnesses

7.Dashboard which is totally removed

Dashboard which is totally removed

Dashboard which is totally removed

2013 Toyota RAV4 dvd player installation:

Work for removal part has finished until here,in fact removal is the main part of upgrading car radio.If you have a clear idea about removal affairs,the next Toyota RAV4 aftermarket navigation installation will not be a hard thing to you.

What you should do can be divided into three parts:make connections with all cables,install new machine and install other parts back to their primary places.

If you feel a little complex to do the connection or other things,you can scan some helpful websites which will give you correct guide,for example:http://www.seicane.com/all-in-one-touch-screen-radio-stereo-for-2013-toyota-rav4-with-3g-wifi-dvd-player-bluetooth-music-tv-tuner-ipod-aux-steering-wheel-control-c247 or you can ask people who knows better about this aspect.

Making sure your security is actually the most important no matter how entertaining that reaching this upgrade goal is.So please having a better understanding about the upgrade as much as possible and making adequate preparations as you can before any work.

Precautions after installation:

1.Please try to make the unit away from heat sources,such as heating,heat or have other things,or it may cause damage to it

2.Please do not let this machine being exposed to rain or moisture in the environment(as when rain or car washing) to avoid the internal machinery of the short circuit caused some danger

3.Before you clean the head unit,you have to shut down power cables and then wipe panel.Without using volatile chemicals to clean trim panel