Are you searching for the methods to upgrade your car’s capacities? If yes, it will be a great idea for you to remove your outdated factory radio and install a brand new multifunctional car radio. And with some related installation experience and the guidance of a correct installation instruction, it will be much easy for you to have a general understanding of the new car radio installation process. The following is a 2004 2005 2006 2007-2010 Toyota Sienna car radio installation instruction. If you happen to own the same car model, then you can take this instruction as a reference.
Before and during installation, you should notice:
1. Before connecting, please make sure the ignition is off to avoid short circuit.
2. Ensure connect the yellow and red power cable at last.
3. Ensure that all loose wires are isolated with electrical tape
4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).
5. Ensure that all ground is connected to the same place.
6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.
7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400
2004 2005 2006 2007-2010 Toyota Sienna car radio installation instruction
1. The original car radio for 2004-2010 Toyota Sienna.
2. Use a flat-head screwdriver or a flat pry tool to pry up the vertical panels of the right and left side of the original car radio and climate control system.
3. Disconnect the wiring from the side panels. There are two wiring connectors on the left panel and only one connector on the right panel. Please carefully press the tab to release the connectors.
4. Remove the center channel speaker grill panel above the car radio. Please use a pry tool or a flat head screwdriver to pry up the top (center channel speaker) panel above the car radio and then remove it.
5. Remove the center speaker. There are two 10mm hex head nuts securing the center speaker, so you need to use a 10-mm Hollow-Shank nut screwdriver to remove these two bolts.
6. Disconnect the speaker wiring harness. Please press the tab down so as to release the wiring connector, and then set the speaker and bolts aside.
7. Remove the 4 10mm hex head nuts from the car radio. There are 4 bolts holding the car radio in the dash (2 on each side). Please use a screwdriver to remove these four bolts.
8. Gently pull the original car radio out of the dash and then disconnect the wiring from the original car radio. Then put the original car radio aside.
9. If necessary, please remove the left and right radio mounting brackets to install on the new Seicane car radio.
10. Check all the accessories for the new Seicane car radio.
11. Connect the harnesses to the back of the new Seicane car radio.
12. Connect the Seicane car radio to your original car radio’s plugs.
13. Gently place the new Seicane car radio into the opening of the dash and test it.
14. Re-seat the stereo in the dash and reinstall the 4 bolts.
15. Carefully reconnect the center speaker and reinstall the 2 bolts.
16. Carefully reinstall top center channel speaker grill panel.
17. Reconnect all the electrical connectors and then reinstall the left and right side panels.
Don’t worry if you cannot fully understand the above removal and installation steps. Under this circumstance, you can contact your dealer, communicate with someone experienced or turn to a professional for help. If you are afraid of making damage to either your car radio or your car, you can also ask a professional technician to help you install the new car radio. Anyway, it is very essential for you to pick an ideal car radio for your beloved car radio. If you don’t know which kind of car radio can fit your car, here I would like to share a remarkable 2004 2005 2006 2007-2010 Toyota Sienna car radio from Seicane with you. For more information, please click:
This powerful car radio is running with the intelligent Android 6.0 operation system and a high-quality quad-core CPU processor to greatly enhance the processing ability.
Even though you are not good at identifying directions, with the assistance of the turn-by-turn directions and voice prompts provided by the 3D GPS navigation system of high precision, you can not only quickly know your current locations but also know the correct way to get to your desired destinations. And while navigating, you can also listen to your favorite music.
Additionally, under the wireless Bluetooth technology, you can make this car radio connect to your Bluetooth-enabled mobile so that you can freely get access to both Bluetooth hands-free phone calls as well as Bluetooth streaming music without taking your hands off the steering wheel. In a word, with this car radio installed in your car, your in-car life will definitely be improved to a new level.
If you like this car radio, just don’t hesitate to add it to your shopping cart right now!