How to remove and install 2010 2011 Mitsubishi Lancer head unit with GPS system IPod WIFI

I guess most of you are curious about how to remove and install 2010 2011 Mitsubishi Lancer head unit with GPS system IPod WIFI if you are interested in installing a new head unit into your car, and today I’d like to show specific installation steps for 2010 2011 Mitsubishi Lancer double din radio to you.

Let’s have a look at a picture first,which is new unit after upgrade,head unit GPS dvd player with touch screen of 2010 2011 Mitsubishi Lancer.Showing this image is to provide a comparison for you to judge that if this unit can be installed in your car.

Do you know that one car stereo may fit several cars actually,this is very possible.And the principles of it are almost same and has little difference.Therefore on matter whether this Mitsubishi Lancer head unit upgrade guide is just for you,you can still have a patient read and learn something which will benefits you.

Nowadays especially in the city roads usage is enlarging very fast and become more complex,so GPS navigation system become very necessary to most drivers,it’s difficult for us to remember all routes in a place especially when we are in a strange place.Therefore many people begin to realize the importance of it.But they are too busy or don’t know how to achieve it.

So today I will give you some advises on how to remove and install the head unit of 2010 2011 Mitsubishi Lancer.

2010 2011 Mitsubishi Lancer radio head unit removal:

1.Open glove compartment and remove screw to side panel

Open glove compartment

Open glove compartment

remove screw to side panel

remove screw to side panel

2.Remove side panel by pulling toward seat

Remove side panel by pulling toward seat

Remove side panel by pulling toward seat

3.Remove screw to trim panel and then gently pull trim piece toward seat

remove screw to trim panel

remove screw to trim panel

gently pull trim piece toward seat

gently pull trim piece toward seat

4.Once trim piece is loose,use panel removal tool or hands to remove trim

once trim piece is loose,use panel removal tool or hands to remove trim

once trim piece is loose,use panel removal tool or hands to remove trim

5.Multiple clips across trim which  holds trim piece in place

Multiple clips across trim which  holds trim piece in place

Multiple clips across trim which holds trim piece in place

6.Attention that do not remove these three screws

do not remove these three screws

do not remove these three screws

7.Use panel removal tool,gently pry edges around stereo face

Use panel removal tool,gently pry edges around stereo face

Use panel removal tool,gently pry edges around stereo face

8.After removing stereo face,place in safe location,tabs along edges of stereo hold stereo face in place

After removing stereo face,place in safe location,tabs along edges of stereo hold stereo face in place

After removing stereo face,place in safe location,tabs along edges of stereo hold stereo face in place

9.Disconnect the connector,and do not turn on vehicle at that time

Disconnect the connector,and do not turn on vehicle at that time

Disconnect the connector,and do not turn on vehicle at that time

10.Remove these four screws that holds stereo in place

Remove these four screws that holds stereo in place

Remove these four screws that holds stereo in place

11.Remove original stereo for access to harnesses behind it

Remove original stereo for access to harnesses behind it

Remove original stereo for access to harnesses behind it

12.Remove smaller connector fto give access to Grom Y-harness

Remove smaller connector fto give access to Grom Y-harness

Remove smaller connector fto give access to Grom Y-harness

2010 2011 Mitsubishi Lancer radio head unit installation:

13.Insert Grom harness into open port of new unit,connect removed harness to Grom Y-harness

Insert Grom harness into open port of new unit

Insert Grom harness into open port of new unit

connect removed harness to Grom Y-harness

connect removed harness to Grom Y-harness

14.20-pin harness connects to Grom unit

20-pin harness connects to Grom unit

20-pin harness connects to Grom unit

15.Separate and test wire for +12v constant

Separate and test wire for +12v constant

Separate and test wire for +12v constant

16.After confirmation of +12v constant,use provided P-Tap to make connection,please ensure P-Tap has punctured wire and is tightly secured

 make connection with help of provided P-Tap

make connection with help of provided P-Tap

17.Fasten top cap to connect Yellow power wire

Fasten top cap to connect Yellow power wire

Fasten top cap to connect Yellow power wire

18.Insert stripped wire as far as possible

Insert stripped wire as far as possible

Insert stripped wire as far as possible

19.Gently secure cap and tug on wire to make sure it is secured

Gently secure cap and tug on wire to make sure it is secured

Gently secure cap and tug on wire to make sure it is secured

20.After making cables connection,turn on stereo and test new unit and hope that you can enjoy your new audio system

Please check the appearance and all functions of original stereo to make sure they can work well before you start to upgrade it and replace a new unit.

After that you only can start up to do your workmore wonderful by yourself.If you need to know better about new installed dvd display,you can visit the following website which has a lot of information there: http://www.seicane.com/double-din-2010-2011-mitsubishi-lancer-aftermarket-gps-radio-system-tv-tuner-cd-dvd-player-3g-wifi-pop-dvr-hd-1080p-video-backup-camera-ipod-iphone-c037.