Install and Upgrade Tutorial for a 2003 2004 2005 2006-2007 Honda Accord 7 GPS Sat Nav Bluetooth Carplay DVR Radio Stereo

2003 2004 2005 2006-2007 Honda Accord 7 car radio after installation

What would you if you want to improve your in-car environment and take your driving experience up a notch? If I were you, I will remove the factory radio and install a new aftermarket car radio, which comes with both practical and entertainment features. If you also plan to replace your factory radio, you can refer to a correct installation guide to help you. This article mainly aims to introduce a 2003 2004 2005 2006-2007 Honda Accord 7 car radio installation guide from Seicane. If you own the same or similar dashboard, you can refer to this guide carefully.

2003 2004 2005 2006-2007 Honda Accord 7 car radio after installation

2003 2004 2005 2006-2007 Honda Accord 7 car radio after installation

Some tips before the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2003 2004 2005 2006-2007 Honda Accord 7 car radio installation guide

1. Use a plastic removal tool to pry the panel on the top of the car radio.

Use a plastic removal tool to pry the panel on the top of the car radio

Use a plastic removal tool to pry the panel on the top of the car radio

2. Pull up the panel and put it aside.

Pull up the panel and put it aside

Pull up the panel and put it aside

3. Use the plastic removal tool to remove the trim part around the gear shifter, and then unplug the connectors or wires at the back.

Use the plastic removal tool to remove the trim part around the gear shifter, and then unplug the connectors or wires at the back

Use the plastic removal tool to remove the trim part around the gear shifter, and then unplug the connectors or wires at the back

4. Get the gear shifter removed to the lower position and then remove the small plastic part which is shown below. Then use a screw driver to unscrew all screws that fix the whole plastic part and then remove it.

Get the gear shifter removed to the lower position and then remove the small plastic part which is shown below. Then use a screw driver to unscrew all screws that fix the whole plastic part and then remove it

Get the gear shifter removed to the lower position and then remove the small plastic part which is shown below. Then use a screw driver to unscrew all screws that fix the whole plastic part and then remove it

4-1

4-1

5. Remove screws that fix the compartment on the bottom of the original car radio and then remove the compartment.

Remove screws that fix the compartment on the bottom of the original car radio and then remove the compartment

Remove screws that fix the compartment on the bottom of the original car radio and then remove the compartment

6. Remove all screws that fix the original car radio.

Remove all screws that fix the original car radio

Remove all screws that fix the original car radio

7. Gently take out the original car radio and unplug the connectors and cables at the back of the radio.

Gently take out the original car radio and unplug the connectors and cables at the back of the radio

Gently take out the original car radio and unplug the connectors and cables at the back of the radio

8. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

9. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

10. Connect the Seicane car radio to your original stereo’s plugs.

11. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

12. Put the new Seicane car radio into the dash.

13. Put everything into their original place. All the installation is done.

 

Now do you have a understanding of 2003 2004 2005 2006-2007 Honda Accord 7 car radio installation? If you have any doubts, you can contact your dealer, communicate with someone experienced or turn to a professional for help. If you still think it hard for you to install a new car radio, you can straightly go to a car radio upgrade center and ask a professional technician to help you install the new car radio. While for the selection of an ideal car radio, you can refer to the following link which is a 2003 2004 2005 2006-2007 Honda Accord 7 car radio from Seicane. For more details, please click:

https://www.seicane.com/android-2003-2007-honda-accord-7-car-stereo-gps-navigation-head-unit-with-1080p-video-bluetooth-music-autoradio-steering-wheel-control-rearview-camera-dvr-4g-wifi-s301188

With this car radio installed in your car, you can freely get access to a wide range of practical and entertainment features, mainly including 3D GPS navigation system of high precision, FM/AM radio tuner, Bluetooth hands-free phone calls, Bluetooth streaming music, file management, SD card or USB connection, etc.

With the assistance of the worldwide real-time GPS navigation system, you can easily locate where you are currently and find the right way to get to any locations you would like to go to according to the turn-by-turn directions and voice prompts. And thanks to this unit’s dual zone function, you can also listen to your favorite music while navigating.

Additionally, this unit comes with built-in Bluetooth module, which enables you to dial, answer, reject and mute Bluetooth hands-free phone calls as well as listen to Bluetooth streaming music from your phone music playlists for both convenience and enjoyment.

If you are interested with this car radio, just install it and enjoy your driving accompanied by it. Good luck!

The Quick Way for a 2008 2009 2010 2011-2015 Mitsubishi Lancer-ex GPS Navigation Bluetooth Car Radio Installation and Upgrade

2008 2009 2010 2011 2012-2015 Mitsubishi Lancer-ex car radio after installation

If you would like to remove your factory radio and install a new car radio, what you need to do is to find out what features you need. And if your factory radio cannot be compatible with these features you are eager to, you can think about replacing your factory radio with a new aftermarket car radio. The following is a detailed 2008 2009 2010 2011-2015 Mitsubishi Lancer-ex car radio installation instruction from Seicane. If you also own the same or similar dashboard, you can refer to this instruction.

2008 2009 2010 2011 2012-2015 Mitsubishi Lancer-ex car radio after installation

2008 2009 2010 2011 2012-2015 Mitsubishi Lancer-ex car radio after installation

Here are four tips about the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-devicesrd-400

 

2008 2009 2010 2011-2015 Mitsubishi Lancer-ex car radio installation instruction

1. Before installation, please remove any CDs from the head unit, and then disconnect the negative from your battery.

Before installation, please remove any CDs from the head unit, and then disconnect the negative from your battery

Before installation, please remove any CDs from the head unit, and then disconnect the negative from your battery

2. Remove trim pieces to access original car radio as follows.

Remove trim pieces to access original car radio as follows

Remove trim pieces to access original car radio as follows

2-1

2-1

2-2

2-2

3. Remove hazard warning accessory.

Remove hazard warning accessory

Remove hazard warning accessory

4. Disconnect Ribbon Harness and wiring loom.

5. Remove car radio fascia, please gently and carefully pull upwards from left hand corner.

Remove car radio fascia, please gently and carefully pull upwards from left hand corner

Remove car radio fascia, please gently and carefully pull upwards from left hand corner

5-1

5-1

6. Remove the four screws that are holding the original car radio in place.

Remove the four screws that are holding the original car radio in place

Remove the four screws that are holding the original car radio in place

7. Gently take out the original car radio.

Gently take out the original car radio

Gently take out the original car radio

8. Remove the original car radio’s wiring harness and antenna from the back of the car radio.

9. Remove the factory mounting brackets and install them on the new car radio.

10. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

11. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

12. Connect the Seicane car radio to your original radio’s plugs.

13. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

14. Put the new Seicane car radio into the dash.

15. Put everything into their original place. All the installation is done.

 

Wish you can learn something useful from the above installation instruction. If you encounter any difficulties and don’t know how to overcome them, you can seek for advice from your dealer or a professional. Or during the installation, you can contact your dealer, communicate with someone experienced or turn to a professional technician. Anyway, before installation, it is essential for you to select an ideal car radio for your beloved car radio. If you have no ideas, you can refer to the following link which is a remarkable 2008 2009 2010 2011-2015 Mitsubishi Lancer-ex car radio from Seicane.

https://www.seicane.com/android-2008-2015-mitsubishi-lancer-ex-hd-touchscreen-gps-navigation-radio-with-fm-bluetooth-wifi-usb-1080p-video-mirror-link-obd2-rearview-camera-s04117

With this car radio installed in your car, you will freely get access to a wide range of practical and entertainment features, such as GPS navigation function, FM/AM radio, Bluetooth hands-free phone calls, Bluetooth streaming music, AUX function, file management, etc. Thus, this all-in-one car radio from Seicane can be taken as one of the most suitable replacements for your factory radio.

Under the guidance of turn-by-turn directions and voice prompts provided by the high-accuracy 3D GPS navigation system, you can easily know your current locations and find the right way to reach your desired destinations even you are driving around an unfamiliar place. And this unit’s dual zone function enables you to listen to your favorite music while navigating.

Through Bluetooth connection between your Bluetooth-enabled mobile phone and this car radio, Bluetooth hands-free phone calls and Bluetooth streaming music are both available for you, which can give you great convenience and enjoyment.

Wish you like this unit and good luck!

How to Install and Upgrade a 2010 2011 2012 2013-2015 KIA Sportage GPS Navigation Bluetooth Head Unit Carplay Audio Radio

2010 2011 2012 2013-2015 KIA Sportage car radio after installation

If your factory radio cannot satisfy you in car since it cannot be compatible with some upgraded features, you can think about replacing your factory radio with a new aftermarket car radio. This article aims to introduce how to remove the factory radio and install the new car radio in 2010 2011 2012 2013-2015 KIA Sportage, if you own the same or similar dashboard, you can carefully refer to the following installation steps, which may help with the installation.

2010 2011 2012 2013-2015 KIA Sportage car radio after installation

2010 2011 2012 2013-2015 KIA Sportage car radio after installation

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-devicesrd-400

 

2010 2011 2012 2013-2015 KIA Sportage car radio installation instruction

1. The original car radio.

The original car radio

The original car radio

2. Uncover the screw covers on each corner and then remove the two screws with a screwdriver.

Uncover the screw covers on each corner and then remove the two screws with a screwdriver

Uncover the screw covers on each corner and then remove the two screws with a screwdriver

2-1

2-1

3. Adjust the steering wheel so as to release the panel on the left side of the radio and then remove it. Don’t forget to disconnect the connectors at the back.

Adjust the steering wheel so as to release the panel on the left side of the radio and then remove it. Don't forget to disconnect the connectors at the back

Adjust the steering wheel so as to release the panel on the left side of the radio and then remove it. Don’t forget to disconnect the connectors at the back

3-1

3-1

3-2

3-2

4. Remove the panel on the right side of the radio with a plastic removal tool.

Remove the panel on the right side of the radio with a plastic removal tool

Remove the panel on the right side of the radio with a plastic removal tool

5. Remove two screws that fixed the radio panel, then remove the panel and unplug the connector at the back.

Remove two screws that fixed the radio panel, then remove the panel and unplug the connector at the back

Remove two screws that fixed the radio panel, then remove the panel and unplug the connector at the back

5-1

5-1

6. Remove four screws that are holding the radio on the dashboard.

Remove four screws that are holding the radio on the dashboard

Remove four screws that are holding the radio on the dashboard

7. Take out the original radio and unplug the connectors at the back of it.

Take out the original radio and unplug the connectors at the back of it

Take out the original radio and unplug the connectors at the back of it

7-1

7-1

8. Check all the accessories for the new Seicane car stereo.

Check all the accessories for the new Seicane car stereo

Check all the accessories for the new Seicane car stereo

9. Connect the harnesses to the back of the new Seicane car stereo.

Connect the harnesses to the back of the new Seicane car stereo

Connect the harnesses to the back of the new Seicane car stereo

10. Connect the Seicane car stereo to your original stereo’s plugs.

11. Turn on the new Seicane car stereo to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

12. Put the new Seicane car stereo into the dash.

13. Put everything into their original place. All the installation is done.

 

Wish you can learn some skills from the above installation instruction. If you meet any difficulties and don’t know how to overcome them, please feel free to contact your dealer, communicate with someone experienced or turn to a professional technician for help. If you still think it hard to install the new car radio, you can directly go to a car radio upgrade center to have the car radio installed by a professional technician.

Anyway, before installation, please carefully pick an ideal car radio for your beloved car. Here I’d like to share a remarkable 2010 2011 2012 2013-2015 KIA Sportage car radio from Seicane with you. Fore more details, please click:

https://www.seicane.com/hd-touchscreen-radio-for-2010-2015-kia-spotage-android-with-gps-navigation-audio-system-bluetooth-music-usb-aux-wifi-1080p-tv-mirror-link-dvr-s0495

This car radio is loaded with the stable Android 6.0 operation system and a powerful quad-core CPU processor, therefore, with this car radio installed in your car, you will embrace a much smoother, faster and easier operation experience.

There are a wide range of practical and entertainment features being offered by this all-in-one car radio, mainly including 3D GPS navigation system, FM/AM radio, Bluetooth hands-free phone calls, Bluetooth streaming music, AUX function, file management, etc.

Under the wireless Bluetooth technology, through the Bluetooth connection between your Bluetooth-enabled mobile phone and this car radio, without taking your hands off the steering wheel, you are able to dial, answer, reject and mute Bluetooth hands-free phone calls as well as listen to Bluetooth streaming music from your phone.

What are you waiting for? This unit is at a competitive price now. If you like it, just add it to your shopping cart.

The Quick Steps of 2014 Honda FIT Left GPS Navigation Car Stereo Bluetooth Radio Installation

2014 Honda FIT Left car radio after installation

It is absolutely correct that an ideal car radio will be regarded as the most important part of a car since it comes with a wide range of practical and entertainment features, mainly including 3D GPS function, Bluetooth function, FM/AM radio tuner, AUX, USB or SD card connection, etc. If you plan to replace your factory radio with a new aftermarket car radio, you can go to a car radio upgrade center or ask a professional to install it in your car. And you can refer to the following    2014 Honda FIT Left car radio installation instruction from Seicane if you own the same or similar dashboard.

2014 Honda FIT Left car radio after installation

2014 Honda FIT Left car radio after installation

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2014 Honda FIT Left car radio installation instruction

1. Remove the bottom panel with a plastic removal tool and then unplug the connector behind.

Remove the bottom panel with a plastic removal tool and then unplug the connector behind

Remove the bottom panel with a plastic removal tool and then unplug the connector behind

1-1

1-1

2. Remove screws below the radio with a screwdriver.

Remove screws below the radio with a screwdriver

Remove screws below the radio with a screwdriver

3. Remove the panel on the left of the radio.

Remove the panel on the left of the radio

Remove the panel on the left of the radio

4. Release the panel one the right side of the radio.

Release the panel one the right side of the radio

Release the panel one the right side of the radio

5. Take out the original radio, please use a plastic removal tool if necessary.

Take out the original radio, please use a plastic removal tool if necessary

Take out the original radio, please use a plastic removal tool if necessary

6. Disconnect the connectors at the back of the radio.

Disconnect the connectors at the back of the radio

Disconnect the connectors at the back of the radio

7. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

8. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

9. Connect the Seicane car radio to your original radio’s plugs.

10. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

11. Put the new Seicane car radio into the dash.

12. Put everything into their original place. All the installation is done.

 

Above is the whole removal and installation process of a 2014 Honda FIT Left car radio. If you are confused with some problems and don’t know how to deal with, you can browse some professional websites for seeking advice, contact your dealer or seek help from a professional. Or you can directly go to a car radio upgrade center and arrange a professional technician to help you install the new car radio. Anyway, before installation, it is very essential for you to pick an ideal car radio. Here I would like to share a remarkable 2014 Honda FIT Left car radio from Seicane with you. For more details, please click:

https://www.seicane.com/2014-honda-fit-left-android-radio-dvd-player-gps-navigation-system-with-touchscreen-bluetooth-4g-wifi-dvr-backup-camera-dab-tpms-s168022

This powerful car radio, which is loaded with the stable Android 6.0 operation system and a high-quality quad-core CPU processor, can largely enhance its capabilities, performance and enjoyment. So it can be regarded as one of the best choices to replace your factory radio in your beloved car.

With the help of the worldwide real-time GPS navigation system of this unit, you are able to easily locate where you are and find the right way to reach any locations you would like to go to according to turn-by-turn directions and voice prompts. Besides, this unit comes with dual zone functions, so you can freely listen to your favorite music while navigating and the music will automatically switch to GPS voice.

What’s more, without keeping your hands off the steering wheel, through the Bluetooth connection between your Bluetooth-enabled mobile phone and this car radio, you are able to dial, answer, reject and mute Bluetooth hands-free phone calls as well as listen to Bluetooth streaming music from your phone music play;lists. Therefore, you can gain great convenience and enjoyment.

What are you waiting for? If you like this unit, just add it to your shopping cart right now.