Tech Guide for a 2013 2014 2015 Volkswagen Passat GPS DVD Car Radio Upgrade with Bluetooth Radio Navigation Audio System

2013 2014 2015 Volkswagen Passat GPS DVD Car Radio after installation

At present, with the rapid development of network, people can freely shop online for buying an ideal car radio. But you still need to pay extra money for its installation if you don’t know how to install it. As a matter of fact, if you have a correct guide as well as some related experience; you can also achieve the installation which can save you a lot of money. The following is the installation guide for a 2013 2014 2015 Volkswagen Passat GPS DVD Car Radio. If you also have the same dashboard, you can refer to the following detailed instruction.

2013 2014 2015 Volkswagen Passat GPS DVD Car Radio after installation

2013 2014 2015 Volkswagen Passat GPS DVD Car Radio after installation

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-devicesrd-400

2013 2014 2015 VW Volkswagen Passat gps dvd car radio installation instruction

1. The original car radio.

The original car radio

The original car radio

2. Open the storage box.

Open the storage box

Open the storage box

3. Pull out the panel and remove it gently. Please use a plastic removal tool to help you with the removal.

Pull out the panel and remove it gently. Please use a plastic removal tool to help you with the removal

Pull out the panel and remove it gently. Please use a plastic removal tool to help you with the removal

3-1

3-1

3-2

3-2

4. Use a T20 screwdriver to remove screws that fixed the radio on the dashboard.

Use a T20 screwdriver to remove screws that fixed the radio on the dashboard

Use a T20 screwdriver to remove screws that fixed the radio on the dashboard

5. Take out the original car radio.

Take out the original car radio

Take out the original car radio

6. Unplug connectors and cables at the back of the radio.

Unplug connectors and cables at the back of the radio

Unplug connectors and cables at the back of the radio

7. Check all the accessories for the new Seicane car radio.

8. Connect the harnesses to the back of the new Seicane car radio.

9. Connect the Seicane car radio to your original radio’s plugs.

10. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

11. Put the new Seicane car radio into the dash.

12. Put everything into their original place. All the installation is done.

 

If you don’t have any related experience before or meet some difficulties you cannot overcome independently, it suggests you to consult your dealer for valuable advice or ask a professional for help. To help you better finish your car radio installation, here I would like to recommend a Seicane 2013 2014 2015 Volkswagen Passat GPS DVD Car Radio to you. For more details, please click:

http://www.seicane.com/10-2-inch-android-2013-2014-2015-vw-volkswagen-passat-radio-with-4g-wifi-bluetooth-mirror-link-cpu-quad-core-touchscreen-steering-wheel-control-s301002

This car radio can be one of your best choices to replace your factory radio. Based on the advanced Android 5.0.1 operation system and featured with a powerful 1.8 GHz Cortex A9 Quad-core CPU processor, this car radio will enable you to embrace the smoothest and fastest operation experience which will undoubtedly surprise you. While as for its function as a multimedia player, it can meet almost all your needs, including playing music, FM/AM radio, video, TV programs, movies, etc. If you like this smart 2013 2014 2015 Volkswagen Passat GPS DVD Car Radio, just remember to add it to your cart. Good luck to you!

How to upgrade a 1998-2005 Mercedes Benz S Class W220 gps navigation system radio with Bluetooth WiFi 1080P Rearview Camera steering wheel control

1998-2005 Mercedes Benz S Class W220 gps navigation system radio after installation

Are you still searching for some methods to achieve the installation of a new gps nav head unit by yourself? Here is a detailed installation instruction for a 1998-2005 Mercedes Benz S Class W220 gps navigation system radio from Seicane. If you have a same vehicle type and are planning to make a head unit replacement for your beloved car, you cam refer to the following installation instruction.

1998-2005 Mercedes Benz S Class W220 gps navigation system radio after installation

1998-2005 Mercedes Benz S Class W220 gps navigation system radio after installation

Here are some tips before the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

1998-2005 Mercedes Benz S Class W220 S280 S320 S350 S400 S430 S500 head unit installation instruction

1. Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside.

Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside

Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside

2. Remove screws that fixed the radio on the dashboard.

Remove screws that fixed the radio on the dashboard

Remove screws that fixed the radio on the dashboard

3. Pull the factory radio out of the dash. Pull it with medium force, as the wires are connected to the radio.

Pull the factory radio out of the dash. Pull it with medium force, as the wires are connected to the radio

Pull the factory radio out of the dash. Pull it with medium force, as the wires are connected to the radio

4. Unplug the connectors at the back of the factory radio.

Unplug the connectors at the back of the factory radio

Unplug the connectors at the back of the factory radio

5. Make antennas and cables connected step by step, and you should be very careful when you are doing this for it will affect whole procedure.

Make antennas and cables connected step by step, and you should be very careful when you are doing this for it will affect whole procedure

Make antennas and cables connected step by step, and you should be very careful when you are doing this for it will affect whole procedure

6. Put the new Seicane radio into your car, you should check whether your connections are correct, and you’d better have a tidy for the cables.

7. If everything is OK, firm screws into their original place.

If everything is OK, firm screws into their original place

If everything is OK, firm screws into their original place

8. Firm the panel on the new Seicane radio. Finally the new Seicane radio is installed and a comprehensive test should be conducted on the new radio.

Firm the panel on the new Seicane radio. Finally the new Seicane radio is installed and a comprehensive test should be conducted on the new radio

Firm the panel on the new Seicane radio. Finally the new Seicane radio is installed and a comprehensive test should be conducted on the new radio

 

Above is the whole installation instruction,wish you can get some help from it.If you cannot understand the steps, you’d better turn to your dealer for help or just directly arrange a professional to install it. Anyway, before the installation, please pay attention to the compatibility between your new head unit and your car. If you don’t have any idea, you can refer to a 1998-2005 Mercedes Benz S Class W220 gps navigation system radio from Seicane. For more details, please click:

http://www.seicane.com/touch-screen-1998-2005-mercedes-benz-s-class-w220-s280-s320-s350-s400-s430-s500-android-radio-gps-navigation-system-with-dvd-bluetooth-wifi-1080p-rearview-camera-steering-wheel-control-s32518

The car radio is loaded with a powerful Android 5.1.1 operation system and a 1.6 GHz Cortex A9 Quad-core CPU, which can provide you with a smoother and faster operation experience. With the guidance of the powerful 3D GPS navigation system of high precision, you are capable of reaching your ideal destinations accurately. Besides, its additional entertainment functions can please both you and your passengers in your car. Wish you like it and have a good day!

How to install a 2008-2013 HONDA CITY gps nav car radio with DVD Player Wifi Backup Camera Bluetooth DVR

2008-2013 HONDA CITY gps nav car radio after installation

When you have a plan to travel around an unfamiliar city, it is very necessary for you to have a multifunctional car radio which can not only come with a powerful GPS navigation system to give you direction guidance but also can work as a multimedia player to relax both you and your passenger. Therefore, if you don’t have a modern car radio that can be compatible with these new features, you’d better replace your factory radio with a upgraded car radio. Here I’d like to share an easy installation instruction for a 2008-2013 HONDA CITY gps nav car radio with you, which can be taken as a reference.

2008-2013 HONDA CITY gps nav car radio after installation

2008-2013 HONDA CITY gps nav car radio after installation

 

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts (Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-devicesrd-400

 

2008-2013 HONDA CITY gps nav car radio installation instruction

1. Remove the bottom panel with a plastic knife.

Remove the bottom panel with a plastic knife

Remove the bottom panel with a plastic knife

2. Remove the two screws under the original radio.

Remove the two screws under the original radio

Remove the two screws under the original radio

3. Pry the top of the original car radio panel with a plastic knife.

Pry the top of the original car radio panel with a plastic knife

Pry the top of the original car radio panel with a plastic knife

4. Then remove the panel.

Then remove the panel

Then remove the panel

5. Take out the original car radio and unplug the connectors behind.

6. Check all the accessories for the new Seicane car radio.

7. Connect the harnesses to the back of the new Seicane car radio.

8. Connect the Seicane car radio to your original stereo’s plugs.

9. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

10. Put the new Seicane car radio into the dash.

11. Put everything into their original place. All the installation is done.

 

That’s all about the 2008-2013 HONDA CITY gps nav car radio installation instruction. Before the installation, if you have any question, you can consult your dealer for seeking good advice. And during the installation, you can ask someone experienced or a professional to help you alongside. Anyway, first of all, you need to check the compatibility between your new car radio with your car. If you don’t have any idea, you can refer to an excellent 2008-2013 HONDA CITY gps nav car radio from Seicane. Here is the related link, please click:

http://www.seicane.com/hd-1024-600-touchscreen-2008-2013-honda-city-8-inch-radio-dvd-player-gps-navigation-system-with-wifi-backup-camera-bluetooth-mirror-link-obd2-dab-dvr-steering-wheel-control-s32777

Upgraded to the latest software and firmware, this 2008-2013 HONDA CITY gps nav car radio is up-to-date enough to replace your factory radio. As this car radio is featured with the advanced Android 5.1.1 operation system as well as a powerful RK3188 1.6 GHz Cortex A9 quad-core processor, you are possible to have the smoothest and fastest in-car operation experience. Its 3D GPS navigation system in high precision enables you to find the best route to reach your ideal destination accurately no matter where you are. Besides, its additional entertainment features can also bring you a ton of fun. Just enjoy your trip with this great car radio in your car. Good luck to you!

To upgrade a 2012 2013 RENAULT DUSTER Bluetooth dvd gps stereo which supports Wifi DAB+ Rearview Camera

2012 2013 RENAULT DUSTER Bluetooth dvd gps stereo after installation

When you plan to upgrade your old factory radio with a new aftermarket car stereo on your own, it is highly suggested that you start your work under the guidance of a correct installation guide. This passage is mainly about a car stereo installation instruction on a 2012 2013 RENAULT DUSTER Bluetooth dvd gps stereo. If you have the same vehicle type, you can refer to this step-by-step car stereo installation guide. Wish you can get some inspiration from it and finish the installation successfully.

2012 2013 RENAULT DUSTER Bluetooth dvd gps stereo after installation

2012 2013 RENAULT DUSTER Bluetooth dvd gps stereo after installation

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-devicesrd-400

 

2012 2013 RENAULT DUSTER car stereo installation guide

1. The original car radio.

The original car radio

The original car radio

2. Release the surrounded panel and the trim panel; please use a removal tool if necessary.

Release the surrounded panel and the trim panel; please use a removal tool if necessary

Release the surrounded panel and the trim panel; please use a removal tool if necessary

2-1

2-1

3. Disconnect connectors at the back of the panel.

Disconnect connectors at the back of the panel

Disconnect connectors at the back of the panel

4. Remove four screws that fixed the radio on the dashboard.

Remove four screws that fixed the radio on the dashboard

Remove four screws that fixed the radio on the dashboard

5. Softly take out the original car radio and disconnect connectors behind.

Softly take out the original car radio and disconnect connectors behind

Softly take out the original car radio and disconnect connectors behind

6. Check all the accessories for the new Seicane car stereo.

7. Connect the harnesses to the back of the new Seicane car stereo.

8. Connect the Seicane car stereo to your original stereo’s plugs.

9. Turn on the new Seicane car stereo to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

10. Put the new Seicane car stereo into the dash.

11. Put everything into their original place. All the installation is done.

 

Above is the installation instruction on a 2012 2013 RENAULT DUSTER Bluetooth dvd gps stereo. Before the installation, please make clear every detailed step. If there is any question, you can seek help from your dealer or a professional. And during the installation, you can ask someone experienced or a technician to help you alongside. However, if you haven’t got a suitable car stereo for your car yet, I would like to recommend a 2012 2013 RENAULT DUSTER Bluetooth dvd gps stereo from Seicane to you. Here comes the link, you may check it for more details:

http://www.seicane.com/2012-2013-renault-duster-android-radio-dvd-player-gps-car-stereo-with-bluetooth-wifi-mirror-link-dab-obd2-backup-camera-sterring-wheel-control-s32787

This 2012 2013 RENAULT DUSTER Bluetooth dvd gps stereo can meet almost your different needs since it is equipped with a variety of upgraded and new features, such as the 3D GPS navigation system, Bluetooth technology, DVD player, FM/AM radio and so on. Therefore, with it, you are able to embrace a brand new driving experience. One of the highlights of this car stereo is that the steering wheel still remains its original functions after its installation. Just take this car stereo and have a great fun with it on all trips!

How to easily install a 2014 SEAT LEON gps dvd audio system with Bluetooth Mirror Link Steering Wheel Control DVR OBD2

2014 SEAT LEON gps dvd audio system after installation

As you can see, there is a good trend that many car owners are pursuing a more convenient, more comfortable in-car life and more relaxing driving experience, so they are very keen on upgrade their radio on their own. In fact, it is also not difficult for you to install a car radio by yourself if you follow a correct installation and have some experience for better.

Now I would like to share an installation instruction on a2014 SEAT LEON gps dvd audio system. If you have a same or similar dashboard, you may refer to it to replace your factory radio.

2014 SEAT LEON gps dvd audio system after installation

2014 SEAT LEON gps dvd audio system after installation

Here are some tips about the installation:

1.Please disconnect the power before the installation.

2.Please prepare a lever and a screwdriver before the removal and the installation.

3.Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd- 400

 

2014 SEAT LEON car radio installation instruction

1. Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside.

Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside

Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside

2. Remove screws that fixed the radio on the dashboard.

Remove screws that fixed the radio on the dashboard

Remove screws that fixed the radio on the dashboard

3. Pull the factory radio out of the dash. Pull it with medium force, as the wires are connected to the radio.

Pull the factory radio out of the dash. Pull it with medium force, as the wires are connected to the radio

Pull the factory radio out of the dash. Pull it with medium force, as the wires are connected to the radio

4. Unplug the connectors at the back of the factory radio.

Unplug the connectors at the back of the factory radio

Unplug the connectors at the back of the factory radio

5. Make antennas and cables connected step by step, and you should be very careful when you are doing this for it will affect whole procedure.

Make antennas and cables connected step by step, and you should be very careful when you are doing this for it will affect whole procedure

Make antennas and cables connected step by step, and you should be very careful when you are doing this for it will affect whole procedure

6. Put the new Seicane radio into your car, you should check whether your connections are correct, and you’d better have a tidy for the cables.

7. If everything is OK, firm screws into their original place.

If everything is OK, firm screws into their original place

If everything is OK, firm screws into their original place

8. Firm the panel on the new Seicane radio. Finally the new Seicane radio is installed and a comprehensive test should be conducted on the new radio.

Firm the panel on the new Seicane radio. Finally the new Seicane radio is installed and a comprehensive test should be conducted on the new radio

Firm the panel on the new Seicane radio. Finally the new Seicane radio is installed and a comprehensive test should be conducted on the new radio

 

 

Before the installation, please make clear every specific step. If you have any questions, you can turn to your dealer for seeking valuable advice. Besides, you can also ask someone experienced or a professional to guide you during the installation. But first of all, please check the compatibility between your new radio and your car. If you don’t have any ideas, you may refer to the following link which is about a remarkable 2014 SEAT LEON gps dvd audio system from Seicane. For more details, please check:

http://www.seicane.com/hd-touchscreen-2014-seat-leon-android-radio-dvd-player-gps-navigation-system-with-bluetooth-mirror-link-steering-wheel-control-wifi-dvr-obd2-dab-backup-camera-s32570

Upgraded to the latest software and firmware, this amazing 2014 SEAT LEON gps dvd audio system can become one of your best choice to replace your factory radio. With it installed in your car, you won’t get lost anymore thanks to the built-in 3D GPS navigation system of high accuracy. And Hands-free calls as well as streaming music from your cell phone are both supported when you realize the connection between this unit and your enabled phone under the Bluetooth technology. Besides, because of its function as a multimedia player, you are able to enjoy your favorite music, videos, FM/AM radio, TV programs, movies, etc. Don’t hesitate to take it home if you like it. Wish you have a good time!

Easy installation instruction on a 2012 2013 2014 VW Volkswagen Passat CC dvd bluetooth car stereo with GPS AUX Rearview Camera

2012 2013 2014 VW Volkswagen Passat CC dvd bluetooth car stereo after installation

You may find your factory radio is out of date since it has been used for a long time and has become insensitive sometimes or it cannot be compatible with some upgraded features. Therefore, it is time for you to consider replacing it with a new one. This article illustrates an installation guide for a 2012 2013 2014 VW Volkswagen Passat CC dvd bluetooth car stereo from Seicane. If you have a same or similar dashboard, you can take it as reference to help with your installation if possible.

2012 2013 2014 VW Volkswagen Passat CC dvd bluetooth car stereo after installation

2012 2013 2014 VW Volkswagen Passat CC dvd bluetooth car stereo after installation

 

Some tips before the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2012 2013 2014 VW Volkswagen Passat CC car stereo installation instruction

1.Lift the latch at the bottom of the decoration panel.

Lift the latch at the bottom of the decoration panel

Lift the latch at the bottom of the decoration panel

2.Remove four screws holding the original radio into the dashboard on the left and right sides with a screwdriver.

Remove four screws holding the original radio into the dashboard on the left and right sides with a screwdriver

Remove four screws holding the original radio into the dashboard on the left and right sides with a screwdriver

3.Take the factory radio out of the dashboard, then unplug all the connectors exposed at the back of it.

Take the factory radio out of the dashboard, then unplug all the connectors exposed at the back of it

Take the factory radio out of the dashboard, then unplug all the connectors exposed at the back of it

4.Connect the GPS aerial for new Seicane car stereo and the rearview camera connectors (optional).

Connect the GPS aerial for new Seicane car stereo and the rearview camera connectors (optional)

Connect the GPS aerial for new Seicane car stereo and the rearview camera connectors (optional)

5.Check all the accessories for the new Seicane car stereo.

Check all the accessories for the new Seicane car stereo

Check all the accessories for the new Seicane car stereo

6.Connect the harnesses to the back of the new Seicane car stereo.

Connect the harnesses to the back of the new Seicane car stereo

Connect the harnesses to the back of the new Seicane car stereo

7.Connect the Seicane car stereo to your original car radio ‘s plugs, and put the new Seicane car stereo into the dash, and fix all the screws.

8.Install the decoration panel and push it inside until the latch lock it.

9.Turn on the new Seicane car stereo to conduct a comprehensive check if all functions work well.

 

Wish the above installation instruction can be helpful for you to some extent. If you cannot deal with some problems independently, you can turn to your dealer for help or just arrange a technician to install the car stereo. Before the installation, please confirm that your new car stereo can fit well with your car. If it is not suitable enough, here I’d like to share a remarkable 2012 2013 2014 VW Volkswagen Passat CC dvd bluetooth car stereo from Seicane. For more information, please click:

http://www.seicane.com/seicane-s121011-10-2-inch-android-radio-dvd-head-unit-gps-system-for-2012-2013-2014-vw-volkswagen-passat-cc-with-bluetooth-mirror-link-obd2-3g-wifi-rearview-camera-dual-way-canbus-aux

This car stereo, specially designed for 2012 2013 2014 VW Volkswagen Passat CC, is intelligent enough for you to upgrade your factory radio. With the high-end GPS navigation system built in this unit, you can be led to your desired destinations through text-to-speech. Through the connection between your enabled cell phone and this car stereo, you can dial, receive or reject hands-free calls as well as enjoy Bluetooth music under the Bluetooth technology. Besides, the additional entertaining features will also add a ton of fun to your driving. Just add it to your cart if you like it!

Ten easy installation steps for a 2003-2014 VW Volkswagen Transporter GPS Bluetooth head unit with Nav OBD2 CD DVD Player CANBUS

2003-2014 VW Volkswagen Transporter GPS Bluetooth head unit after installation

Have you ever upgraded your factory radio? If yes, you may think it not hard to install a new head unit. If not, you might as well learn how to replace your factory radio with a brand new one from now on. Today I would like to share a detailed 2003-2014 VW Volkswagen Transporter GPS Bluetooth head unit installation guide from Seicane with you. Whether you are a veteran or a novice, if you have a same or similar dashboard, you can follow it step by step and wish it can help with your installation.

2003-2014 VW Volkswagen Transporter GPS Bluetooth head unit after installation

2003-2014 VW Volkswagen Transporter GPS Bluetooth head unit after installation

Some tips before the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2003-2014 VW Volkswagen Transporter head unit installation instruction

1.Remove the original radio with the unlock tools.

Remove the original radio with the unlock tools

Remove the original radio with the unlock tools

2.Disconnect the harness in the back.

Disconnect the harness in the back

Disconnect the harness in the back

3.Unplug the connectors.

Unplug the connectors

Unplug the connectors

4.Disconnect the car radio wiring.

Disconnect the car radio wiring

Disconnect the car radio wiring

5.Remove screws behind the console.

Remove screws behind the console

Remove screws behind the console

6.Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

7.Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

8. Connect the Seicane car radio to your original car radio ‘s plugs.

9. Put the new Seicane radio into dash.

10. Make sure everything is ok and turn on the new Seicane car radio. If it doesn’t, please check whether all the cables are connected correctly.

 

Wish you can achieve your installation process successfully under the guidance of the related installation guide. When you encounter some problems, you can seek help from your dealer or a professional. Or you can ask someone experienced to teach you how to finish the installation. However, if you haven’t had a suitable head unit for your car, you can take this 2003-2014 VW Volkswagen Transporter GPS Bluetooth head unit from Seicane into consideration, please click:

http://www.seicane.com/seicane-s127402-quad-core-android-2003-2014-vw-volkswagen-transporter-radio-bluetooth-in-dash-car-navigation-system-with-3g-wifi-mirror-link-obd2-cd-dvd-player-16g-flash-rearview-camera-canbus

With this intelligent 2003-2014 VW Volkswagen Transporter GPS Bluetooth head unit installed in your car, you will embrace a brand new driving experience. The powerful high-precision 3D GPS navigation system allows you to reach anywhere through its turn-by-turn directions and voice prompts. The Bluetooth module allows you to have hands-free calls as well as Bluetooth music when you easily make this unit sync with your Bluetooth-enabled cell phone, which offers you a safer and happier journey. Just enjoy your driving in the company of this unit!

How to easily remove and install a 1998-2006 Mercedes Benz G Class W463 double din car stereo with 16G Flash Mirror Link

1998-2006 Mercedes Benz G Class W463 double din car stereo after installation

If your factory radio cannot be compatible with many upgraded and brand new features, it strongly suggests you to quit it without hesitation and install an advanced car stereo. An upgraded car stereo can not only improve your in-car environment but also take your driving experience up a notch. Besides, it is easy to install a car stereo by yourself under a correct detailed guide. This article is mainly about how to upgrade a 1998-2006 Mercedes Benz G Class W463 double din car stereo. If you have a same or similar dashboard as followings, you may refer to it.

1998-2006 Mercedes Benz G Class W463 double din car stereo after installation

1998-2006 Mercedes Benz G Class W463 double din car stereo after installation

 

Some tips before the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

1998-2006 Mercedes Benz G Class W463 G550 G500 G400 car stereo installation guide

1.The original car radio.

The original car radio

The original car radio

2.Use a special plastic tool to remove the trim bazel.

Use a special plastic tool to remove the trim bazel

Use a special plastic tool to remove the trim bazel

2-1

2-1

3. Use a plastic remove tool to push up the heat vent.

Use a plastic remove tool to push up the heat vent

Use a plastic remove tool to push up the heat vent

3-1

3-1

4.Remove 2 hidden screws with a screwdriver below the vent.

Remove 2 hidden screws with a screwdriver below the vent

Remove 2 hidden screws with a screwdriver below the vent

4-1

4-1

5. Push down the vent and loose it.

Push down the vent and loose it

Push down the vent and loose it

6.Remove the trim panel with a plastic removal tool.

Remove the trim panel with a plastic removal tool

Remove the trim panel with a plastic removal tool

7. Remove 2 screws that are holding the car radio.

Remove 2 screws that are holding the car radio

Remove 2 screws that are holding the car radio

8.Take out the original car radio.

Take out the original car radio

Take out the original car radio

9.Unplug the connectors and cables at the back of the radio.

Unplug the connectors and cables at the back of the radio

Unplug the connectors and cables at the back of the radio

10. Check all the accessories for the new Seicane car stereo.

Check all the accessories for the new Seicane car stereo

Check all the accessories for the new Seicane car stereo

11.Connect the harnesses to the back of the new Seicane car stereo.

Connect the harnesses to the back of the new Seicane car stereo

Connect the harnesses to the back of the new Seicane car stereo

12. Connect the Seicane car stereo to your original stereo’s plugs.

13.Turn on the new Seicane car stereo to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

14.Put the new Seicane car stereo into the dash.

15.Put everything into their original place. All the installation is done.

 

Do you think the above installation guide is complicated for you to understand? If you meet with difficulties, you can seek advice from your dealer or ask a professional for help. But if you don’t know how to choose an ideal car stereo for your car, you can check out the following link which is about a 1998-2006 Mercedes Benz G Class W463 double din car stereo from Seicane, which can be taken as your reference.

http://www.seicane.com/seicane-s127507-pure-android-autoradio-bluetooth-multimedia-navigation-system-for-1998-2006-mercedes-benz-g-class-w463-g550-g500-g400-with-3g-wifi-radio-tuner-dvd-flash-mirror-link-obd2-s127507

This marvelous car stereo for 1998-2006 Mercedes Benz G Class W463 G550 G500 G400, armed with adigital HD 1024*600 multi-touch screen, will provide you more sensitive operation as well as better viewing effect. Thanks to the powerful 3D GPS navigation system in high precision, you can be led to your desired destinations anywhere and anytime. As to entertaining options, this unit allows you to play CDs, VCDs, Bluetooth music, FM/AM radio, videos, TV programs, which can bring you a lot of joyfulness when you have a long-time driving. Wish you like it and have a good time!

Details steps to remove and install a 1998-2005 BMW M3 audio system head unit with dvd gps radio USB SD

1998-2005 BMW M3 audio system head unit after installation

Have you got a multifunctional car head unit and regard it as your best road companion? If not, it is a wise idea for you to install an all-in-one head unit which can bring you a brand new driving experience. Don’t worry that whether it is too complicated to install a new head unit on your own. Actually, with a correct installation guide and some related experience, you can succeed in the head unit installation. Here comes a 1998-2005 BMW M3 audio system head unit installation guide for you as a reference if you have interest in installing a head unit by yourself.

1998-2005 BMW M3 audio system head unit after installation

1998-2005 BMW M3 audio system head unit after installation

 

Before and during installation, you should notice:

1.Before connecting, please make sure the ignition is off to avoid short circuit.

2.Ensure connect the yellow and red power cable at last.

3.Ensure that all loose wires are isolated with electrical tape

4.Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5.Ensure that all ground is connected to the same place.

6.Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-devicesrd-400

 

1998-2005 BMW M3 head unit installation instruction

1.The original head unit.

The original head unit

The original head unit

2.Remove the decoration strip, pry from the gap by using a flathead screwdriver.

Remove the decoration strip, pry from the gap by using a flathead screwdriver

Remove the decoration strip, pry from the gap by using a flathead screwdriver

2-1

2-1

3.Remove the two fixed screws from the original head unit.

Remove the two fixed screws from the original head unit

Remove the two fixed screws from the original head unit

4.Gently remove the original head unit.

Gently remove the original head unit

Gently remove the original head unit

5.Unplug the power speaker cable(by using a flathead screwdriver) and radio antenna.

Unplug the power speaker cable(by using a flathead screwdriver) and radio antenna

Unplug the power speaker cable(by using a flathead screwdriver) and radio antenna

5-1

5-1

6.Remove the air conditioning control panel. By putting two hands on the air conditioning control panel, and pull it out toward to your own direction.

Remove the air conditioning control panel. By putting two hands on the air conditioning control panel, and pull it out toward to your own direction

Remove the air conditioning control panel. By putting two hands on the air conditioning control panel, and pull it out toward to your own direction

7.Pull out the related wires.

Pull out the related wires

Pull out the related wires

8.Remove the air-conditioning vents. The vent is firmly fixed, press it by 2 thumbs and remove it when the vent come out.

Remove the air-conditioning vents. The vent is firmly fixed, press it by 2 thumbs and remove it when the vent come out

Remove the air-conditioning vents. The vent is firmly fixed, press it by 2 thumbs and remove it when the vent come out

9.Remove the final two screws from the frame, so as to take out the whole unit frame.

Remove the final two screws from the frame, so as to take out the whole unit frame

Remove the final two screws from the frame, so as to take out the whole unit frame

10. Take out the storage box inside, where to install with air conditioning control panel.

11. Check all the accessories for the new Seicane head unit.

12. Connect the harnesses to the back of the new Seicane head unit.

13. Connect the Seicane head unit to your original stereo’s plugs.

14. Turn on the new Seicane head unit to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

15. Put the new Seicane head unit into the dash.

16.Put everything into their original place. All the installation is done.

 

 

Wish the above guide can help with your installation on a 1998-2005 BMW M3 audio system head unit. If there are any questions with your installation, it is suggested that you should seek help from your dealer or a professional. But before the installation, please confirm that you have a right head unit that fits your 1998-2005 BMW M3 very well. If it is not suitable enough, I would like to share an up-to-date 1998-2005 BMW M3 audio system head unit from Seicane for you.

http://www.seicane.com/1998-2005-bmw-m3-hd-1024-600-touch-screen-radio-gps-dvd-player-navigation-system-with-ipod-bluetooth-obd2-dvr-rearview-camera-tv-1080p-video-3g-wifi-steering-wheel-control-usb-sd-mirror-link-s167212

This remarkable 1998-2005 BMW M3 audio system head unit reveals its super high performance and its great utility since it is armed with the most advanced Android 5.1.1 based system as well as a RK3188 1.6 GHz Cortex A9 quad-core processor. The 3D GPS navigation system of high accuracy is built up for you to find the correct directions to your desired destinations through lane assist route planning, turn-by-turn directions and voice prompts. With the assistance of Bluetooth technology, you can easily sync your enabled cell phone with this unit for hands-free calls and steaming music with remaining you hands on the steering wheel, which ensure your driving safety as well as amusement. Wish you like it. Good luck to you!

How to easily upgrade a 2011-2014 Hyundai HG gps head unit supports HD 1024*600 touch screen OBD2 DVR backup camera

2011-2014 Hyundai HG gps head unit after installation

Have you consider changing your factory radio with an up-to-date head unit when you find you find the factory radio is not intelligent enough to be compatible with many modern features. A new aftermarket head unit is integrated with a wide range of practical and entertainment features, which will take your driving experience up a notch. So if you have some interest in installing a head unit, it’s suggested you read this article which is about a 2011-2014 Hyundai HG gps head unit installation guide.

2011-2014 Hyundai HG gps head unit after installation

2011-2014 Hyundai HG gps head unit after installation

 

Before and during installation, you should notice:

1.Before connecting, please make sure the ignition is off to avoid short circuit.

2.Ensure connect the yellow and red power cable at last.

3.Ensure that all loose wires are isolated with electrical tape

4.Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5.Ensure that all ground is connected to the same place.

6.Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-devicesrd-400

 

2011-2014 Hyundai HG gps head unit installation guide

1.Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside.

Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside

Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside

2.Remove screws that fixed the radio on the dashboard.

Remove screws that fixed the radio on the dashboard

Remove screws that fixed the radio on the dashboard

3.Pull the factory radio out of the dash. Pull it with medium force, as the wires are connected to the radio.

Pull the factory radio out of the dash. Pull it with medium force, as the wires are connected to the radio

Pull the factory radio out of the dash. Pull it with medium force, as the wires are connected to the radio

4.Unplug the connectors at the back of the factory radio.

Unplug the connectors at the back of the factory radio

Unplug the connectors at the back of the factory radio

5. Make antennas and cables connected step by step, and you should be very careful when you are doing this for it will affect whole procedure.

Make antennas and cables connected step by step, and you should be very careful when you are doing this for it will affect whole procedure

Make antennas and cables connected step by step, and you should be very careful when you are doing this for it will affect whole procedure

6.Put the new Seicane radio into your car, you should check whether your connections are correct, and you’d better have a tidy for the cables.

7.If everything is OK, firm screws into their original place.

If everything is OK, firm screws into their original place

If everything is OK, firm screws into their original place

8.Firm the panel on the new Seicane radio. Finally the new Seicane radio is installed and a comprehensive test should be conducted on the new radio.

Firm the panel on the new Seicane radio. Finally the new Seicane radio is installed and a comprehensive test should be conducted on the new radio

Firm the panel on the new Seicane radio. Finally the new Seicane radio is installed and a comprehensive test should be conducted on the new radio

 

 

That’s all about the installation steps to install a 2011-2014 Hyundai HG gps head unit. Please confirm that you are very clear about every detailed step before the installation. If there is something wrong with your installation, you may consult your dealer for valuable suggestions. Or you can seek help from a professional.  Whatever you encounter, please check the compatibility between your new head unit with your car. If you have no idea, you can refer to a marvelous 2011-2014 Hyundai HG gps head unit from Seicane. For more details, please click:

http://www.seicane.com/oem-android-radio-gps-dvd-player-for-2011-2014-hyundai-hg-with-navigation-system-hd-1024-600-touch-screen-obd2-dvr-rearview-camera-tv-3g-wifi-steering-wheel-control-usb-sd-bluetooth-1080p-video-mirror-link-s168068

The 2011-2014 Hyundai HG gps head unitof high quality with the most up-to-date Android 5.1.1 operation system and the powerful 1.6 GHZ Cortex A9 Quad-core CPU can be one of your best choices to replace your factory radio. There are plenty of entertainment options provided to relax yourself, your families or friends in your car, including playing movies, TV programs, CDs, FM/AM radio, music and so on. Wish you can embrace an excellent driving experience with this intelligent device installed in your beloved car. Good luck to you!