Detailed installation steps for 2009 2010 2011 2012 OPEL Antara navigation system with TV Bluetooth iPod iPhone 

You can watch next video firstly,which will show you main functions of aftermarket stereo for OPEL Antara.

Would you like to upgrade your car audio system without other people’s help if you are a owner of 2009 2010 2011 2012 OPEL Antara?

Some people may say that is impossible,however facts shows that there are a lot of people have done it successfully with the help of detailed installation steps for 2009 2010 2011 2012 OPEL Antara navigation system with TV Bluetooth iPod iPhone.

I know one kind of head unit which matches OPEL Antara of 2009 2010 2011 2012,if you have interest in it,you can visit next website,which may provide you some helpful information: http://www.seicane.com/all-in-one-multimedia-navigation-system-for-2009-2012-opel-antara-with-gps-radio-tv-bluetooth-ipod-iphone-support-3d-navigation-3g-wifi-dvd-function-c019-1.

Installing aftermarket GPS dvd in car is not a very difficult thing especially when you have made much preparations for it.It includes choosing a right machine for your beloved car,making  clear specific upgrade steps for it and preparing tool which may needed in the following process.

2009-2012 OPEL Antara car stereo removal and installation:

1.There are four small holes on original radio if you watch very closely, insert two removal tools into 4 holes

insert two removal tools into 4 holes

insert two removal tools into 4 holes

2.Gently drag the stereo out at the same time

Gently drag the stereo out at the same time

Gently drag the stereo out at the same time

3.Disconnect cables behind the unit

Disconnect cables behind the unit

Disconnect cables behind the unit

4.Make a screw out and make wires placed in inner place

Make a screw out and make wires placed in inner place

Make a screw out and make wires placed in inner place

5.Pry top position of trim panel,loosen and remove it

Pry top position of trim panel,loosen and remove it

Pry top position of trim panel,loosen and remove it

6.When you have removed the panel,connect cables which are taken out

When you have removed the panel,connect cables which are taken out

When you have removed the panel,connect cables which are taken out

connect cables which are taken out

connect cables which are taken out

7.Drag out this side panel a little with a screwdriver,then make lower side panel off which is in front of file

Drag out this side panel a little with a screwdriver

Drag out this side panel a little with a screwdriver

make lower side panel off which is in front of file

make lower side panel off which is in front of file

8.Insert long red line down through the side fastened panel and up through removed panel in front of file,fix the side panel

Insert long red line down through the side fastened panel and up through removed panel in front of file,fix the side panel

Insert long red line down through the side fastened panel and up through removed panel in front of file,fix the side panel

9.Sort well wires as the picture show

Sort well wires as the picture show

Sort well wires as the picture show

10.Plug long red cable to right interface

Plug long red cable to right interface

Plug long red cable to right interface

11.Make it connected with small panel which is removed in front of file,then cover it

Make it connected with small panel which is removed in front of file,then cover it

Make it connected with small panel which is removed in front of file,then cover it

12.Make connection on all cables connection between new stereo and the car

Cables connection step1

Cables connection step1

Cables connection step2

Cables connection step2

13.Insert   two outside cables into new unit’s back place,install new stereo into it,and cover removed panel on the dvd player

Here is the new unit after installation,gps dvd navigation system of 2009 2010 2011 2012 OPEL Antara.

New unit after installation,gps dnew unit after installation,gps dvd navigation system of 2009 2010 2011 2012 OPEL Antaravd sound system of 2009 2010 2011 2012 OPEL Antara

New unit after installation,gps dvd navigation system of 2009 2010 2011 2012 OPEL Antara

 

If you have finished removing the original CD radio and installing OPEL Antara navigation system in your car smoothly,you will surely be very interested in using the new head unit.

It has increased a lot of useful functions,such as gps navigation system and support all TV systems.Even if you are experienced in electronic products,it’s a new challenge to you after all.

I suggest you to search useful information as much as possible,which can mainly achieve on the Internet.And if you want to find more different kinds of stereos,you can have a view at next one: http://www.seicane.com.

 

 

Easy installation steps for 2009 2010 2011 2012 Ford F250 navigation system

Hi friends,are you the owner of 2009-2012 Ford F250 and have you upgraded your car’s audio system to gps navigation system?

With rapid development of technology,new dvd radio which fits your car series have been produced and some new functions are increased and some original functions become more advanced.For example the GPS system,which is very helpful when someone who are easy to get lost or be lazy to remember routes.

But before that you can have a look at following head unit after installation,DVD gps navigation audio system of 2009 2010 2011 2012 Ford F250,and you need to make a comparison with your factory one.

Head unit after installation,DVD gps navigation audio system of 2009 2010 2011 2012 Ford F250

Head unit after installation,DVD gps navigation audio system of 2009 2010 2011 2012 Ford F250

You can make the decision whether you can install a unit like this one into your car and then we come to talk about easy installation steps for 2009 2010 2011 2012 Ford F250 navigation system.

If you have made up your mind to upgrade the head unit of your car,but you know little about it and its upgrade,then you can surf the Internet and visit some websites,for example:http://www.seicane.com/8-inch-2009-2010-2011-2012-ford-f150-f250-f350-expedition-sat-nav-car-a-v-system-lcd-touch-screen-cd-dvd-player-bluetooth-tv-radio-tuner-wifi-3g-aux-auto-a-v-ipod-iphone-1080p-pop-mp3-backup-camera-c222,which can help you get some detailed description and workers who are more professional,they can help you deal with some problems.

In addition,knowing how to operate this new unit is very necessary for your long time usage,here is an exact video which is more intuitive,you can have a view at it:

Except F250,this unit fits F150 and F350.When we have acknowledged so much about aftermarket Ford F250 navigation system,then let’s begin theme today.Before you begin any work,please remember to disconnect negative power cable to ensure safety.

2009-2012 Ford F250 radio removal and dvd GPS installation:

1.Make the rubber pad at the top of the trim panel off the unit

Make the rubber pad at the top of the trim panel off the unit

Make the rubber pad at the top of the trim panel off the unit

2.Make out the exposed 2 screws

Make out the exposed 2 screws

Make out the exposed 2 screws

3.Loosen and pull the side panels containing the a/c vents away from its trim panel.Please note that it is not necessary to remove the panels completely

Loosen and pull the side panels containing the a/c vents away from its trim panel

Loosen and pull the side panels containing the a/c vents away from its trim panel

4.Fasten and remove trim panel of the stereo

Fasten and remove trim panel of the stereo

Fasten and remove trim panel of the stereo

5.Make all molex plugs unplugged

Make all molex plugs unplugged

Make all molex plugs unplugged

6.Remove 4 screws,and then remove the factory radio

Remove 4 screws,and then remove the factory radio

Remove 4 screws,and then remove the factory radio

7.Take out stereo gently and  make connectors unplugged

Take out stereo gently

Take out stereo gently

 make connectors unplugged

make connectors unplugged

After successful removal work,then we continue to upgrade the stereo.When you are sure that your bought unit fits your car,read installation instructions carefully and tidy well all wires as neatly as possible.

After correct connection,install the new radio into the space.Look around in your car to make sure that you can find screws,panel and pad that are removed before,to use again at later time.

Turn on Ford F250 new head unit,and see whether all functions can operate.If they are ok,it means that your actions are right.But do not be so excited that you do wrong operations to new unit and car,your safety should be ensured at any time.You may try on it and enjoy a wonderful journey.

Precautions after installation:

I advise you to take care of following notes to make this gps dvd radio can be used longer.

Please use your finger or the touch screen pen if you have to gently operate the unit,without using any other sharp objects;try to keep the screen as clean as possible;In addition,note that not to splash any liquid on the screen to avoid unnecessary damage to the stereo.

 

 

OEM 2012 Nissan Patrol navigation system with 3G WIFI installation

Pursuing more entertaining and comfortable life has became a  trend in daily life,and upgrading car stereos is one of the methods to realize it.

In fact you can achieve it by yourself if you know much about oem 2012 Nissan Patrol navigation system with 3G WIFI installation.So to friends who want to achieve it yourself,then you need to know clearly about how to remove 2012 Nissan Patrol audio system cd radio.

At first,we can have a look at following at next picture:2012 Nissan Patrol aftermarket audio stereo navigation system with bluetooth 3G WIFI.

2012 Nissan Patrol aftermarket audio stereo navigation system with bluetooth 3G WIFI

2012 Nissan Patrol aftermarket audio stereo navigation system with bluetooth 3G WIFI

Before installation,you must ensure that this unit is suitable for your car and then go on following behind actions.If you are not sure,you can ask someone who works in the market or workers on the website,for example:http://www.seicane.com/radio-replacement-aftermarket-oem-gps-car-a-v-system-for-2012-nissan-patrol-with-3g-wifi-dvr-bluetooth-music-dvd-recoding-function-support-c154.And if this is doesn’t fit yours,maybe you can find another suitable one there.

Here are some preparation works,include disconnect negative power cable,park your car well and turn off original radio and other car series to ensure security.

2012 Nissan Patrol original audio system removal:

1.This is original car stereo

original car stereo

original car stereo

2.Use a lever to pry top trim panel and remove it gently,then you can put it on the right side

Use a lever to pry top trim panel and remove it gently

Use a lever to pry top trim panel and remove it gently

3.Make out the screw with a screwdriver,then we come to below part

Make out the screw

Make out the screw

4.Make the lowest panel a little off the unit,then pry higher bigger panel with a lever

Make the lowest panel a little off the unit,then pry higher bigger panel with a lever

Make the lowest panel a little off the unit,then pry higher bigger panel with a lever

5.Make  this whole panel off,lay it conversely on your legs

Make  this whole panel off

Make this whole panel off

6.Make these 2 screws off with a screwdriver,and 2 screws under them

Make these 2 screws off with a screwdriver

Make these 2 screws off with a screwdriver

 

and 2 screws under them

and 2 screws under them

7.Then you can remove factory stereo,turn it over and unplug the right cable as the picture show and remove the other two with a removal tool

remove factory stereo,turn it over and unplug the right cable

remove factory stereo,turn it over and unplug the right cable

remove the other two with a removal tool

remove the other two with a removal tool

Precautions during audio removal:

1.Please be gentle and careful to removed objects to avoid any damage

2.Put screws on available places after you have removed them,for you will use them to firm stereo and other systems at later time

3.Have a check to the new unit to see whether your new bought stereo can be installed in after you have removed original one

2012 Nissan Patrol navigation system installation:

8.Firstly,you should figure out how to connect antennas by carefully reading instructions and behave it according to it.And you’d better have a check after that if you are not very sure for it matters a lot

9.After that,install new radio into right space and then turn on it to see if everything is right

10.At last,when you have succeed finishing above steps,then install screws back on new unit to fix it,make removed trim panels back to primary positions

You can do your Nissan Patrol navigation installation with the help of above instructions,and main principles of it is same to many other car stereo installation.So you can also apply it to yours though you are not a owner of Nissan Patrol.

I am sure that you will benefit a lot from some new functions,such as GPS navigation system,HD touch screen and it also support all TV systems.But still notice that you can enjoy them under the condition that you are driving safely.

 

How to install 2012 2013 Chevrolet Colorado navigation system with BT touch screen

Car stereo audio after installation,GPS radio audio with navigation system of 2012 2013 Chevrolet Colorado.

Car stereo audio after installation,GPS radio audio with navigation system of 2012 2013 Chevrolet Colorado

Car stereo audio after installation,GPS radio audio with navigation system of 2012 2013 Chevrolet Colorado

I guessyou may be curious about this new stereo for it’s a little different from your factory one on its outward and features.New unit’s screen is a touch screen which can be operated by a special touch screen pen.And it has increased some convenient and entertaining functions,if you want to know it more detail,you can visit some related websites,for example:http://www.seicane.com/oem-aftermarket-car-audio-bluetooth-dvd-player-for-chevrolet-colorado-with-3g-wifi-gps-e-book-a2dp-support-radio-upgrade-can-bus-c203 . It should be more convenient if your Chevrolet Colorado has upgraded car audio.

So many drivers would like to install one but have no idea about how to install 2012 2013 Chevrolet Colorado navigation system with BT touch screen.Don’t worry,it’s not hard to behave and also doesn’t need much professional skills,it just need you to be patient to know its operation and careful to do it.

I will show you detailed installation steps for Chevrolet Colorado navigation system in the following part,please be patient to read it and hope you will benefit a lot. 2012 2013 Chevrolet Colorado radio removal and nav system installation: 1.Gently pry the upper vent housing panel from the dash with a panel removal tool

Gently pry the upper vent housing panel from the dash with a panel removal tool

Gently pry the upper vent housing panel from the dash with a panel removal tool

2.Lever the shifter surround panel,on manual transmission vehicles,unclip and reposition the shifter

Lever the shifter surround panel,on manual transmission vehicles,unclip and reposition the shifter

Lever the shifter surround panel,on manual transmission vehicles,unclip and reposition the shifter

3.Make out 2 screws from the storage pocket,remove storage

Make out 2 screws from the storage pocket,remove storage

Make out 2 screws from the storage pocket,remove storage

4.Make out 4 screws from the accessorv control panel

Make out 4 screws from the accessorv control panel

Make out 4 screws from the accessorv control panel

Make out 4 screws from the accessorv control panel

Make out 4 screws from the accessorv control panel

5.Pull out on panel,this panel was very tough to remove,be patient and the clips will release let panel hang to side

Pull out on panel

Pull out on panel

6.Make out 2 screws from the radio control panel, disconnect the radio control panel

Make out 2 screws from the radio control panel

Make out 2 screws from the radio control panel

7.This is a really strange blue clip you must make out the blue clip completely before removing the real connector,and remove the other clip

make out the blue clip completely before removing the real connector

make out the blue clip completely before removing the real connector

8.Make out 2 screws from the radio chassis,and 2 screws near the top of the stereo to release the screen

Make out 2 screws from the radio chassis

Make out 2 screws from the radio chassis

and 2 screws near the top of the stereo to release the screen

and 2 screws near the top of the stereo to release the screen

9.Make out screen by pulling out,remove behind clip

Make out screen by pulling out,remove behind clip

Make out screen by pulling out,remove behind clip

10.Make out 2 more screws on stereo

Make out 2 more screws on stereo

Make out 2 more screws on stereo

11.Make out the unit and connectors

Make out the unit and connectors

Make out the unit and connectors

You see,removal affairs has been finished,the following thing is to install a new stereo for your beloved car,and this following part  is actually easier than removing steps.

When you have carefully read over installation instructions,make corresponding cables connection which you should try to make sure it precise.Please pay more attention on this because it’s very important to your installation.

After that sort some disordered antennas and install new unit gently into the right space. Turn on new unit and have a careful check for your installed head unit to see whether it can work properly.If the answer is yes,then continue actions including screwing screws tight to original places and reinstalling storage and trim panel to make everything back.

You will enjoy very good time after you have finished whole procedure and drive a car with such a multimedia dash dvd with GPS bluetooth touch screen.

How to remove and install 2010 2011 Mitsubishi Lancer head unit with GPS system IPod WIFI

I guess most of you are curious about how to remove and install 2010 2011 Mitsubishi Lancer head unit with GPS system IPod WIFI if you are interested in installing a new head unit into your car, and today I’d like to show specific installation steps for 2010 2011 Mitsubishi Lancer double din radio to you.

Let’s have a look at a picture first,which is new unit after upgrade,head unit GPS dvd player with touch screen of 2010 2011 Mitsubishi Lancer.Showing this image is to provide a comparison for you to judge that if this unit can be installed in your car.

Do you know that one car stereo may fit several cars actually,this is very possible.And the principles of it are almost same and has little difference.Therefore on matter whether this Mitsubishi Lancer head unit upgrade guide is just for you,you can still have a patient read and learn something which will benefits you.

Nowadays especially in the city roads usage is enlarging very fast and become more complex,so GPS navigation system become very necessary to most drivers,it’s difficult for us to remember all routes in a place especially when we are in a strange place.Therefore many people begin to realize the importance of it.But they are too busy or don’t know how to achieve it.

So today I will give you some advises on how to remove and install the head unit of 2010 2011 Mitsubishi Lancer.

2010 2011 Mitsubishi Lancer radio head unit removal:

1.Open glove compartment and remove screw to side panel

Open glove compartment

Open glove compartment

remove screw to side panel

remove screw to side panel

2.Remove side panel by pulling toward seat

Remove side panel by pulling toward seat

Remove side panel by pulling toward seat

3.Remove screw to trim panel and then gently pull trim piece toward seat

remove screw to trim panel

remove screw to trim panel

gently pull trim piece toward seat

gently pull trim piece toward seat

4.Once trim piece is loose,use panel removal tool or hands to remove trim

once trim piece is loose,use panel removal tool or hands to remove trim

once trim piece is loose,use panel removal tool or hands to remove trim

5.Multiple clips across trim which  holds trim piece in place

Multiple clips across trim which  holds trim piece in place

Multiple clips across trim which holds trim piece in place

6.Attention that do not remove these three screws

do not remove these three screws

do not remove these three screws

7.Use panel removal tool,gently pry edges around stereo face

Use panel removal tool,gently pry edges around stereo face

Use panel removal tool,gently pry edges around stereo face

8.After removing stereo face,place in safe location,tabs along edges of stereo hold stereo face in place

After removing stereo face,place in safe location,tabs along edges of stereo hold stereo face in place

After removing stereo face,place in safe location,tabs along edges of stereo hold stereo face in place

9.Disconnect the connector,and do not turn on vehicle at that time

Disconnect the connector,and do not turn on vehicle at that time

Disconnect the connector,and do not turn on vehicle at that time

10.Remove these four screws that holds stereo in place

Remove these four screws that holds stereo in place

Remove these four screws that holds stereo in place

11.Remove original stereo for access to harnesses behind it

Remove original stereo for access to harnesses behind it

Remove original stereo for access to harnesses behind it

12.Remove smaller connector fto give access to Grom Y-harness

Remove smaller connector fto give access to Grom Y-harness

Remove smaller connector fto give access to Grom Y-harness

2010 2011 Mitsubishi Lancer radio head unit installation:

13.Insert Grom harness into open port of new unit,connect removed harness to Grom Y-harness

Insert Grom harness into open port of new unit

Insert Grom harness into open port of new unit

connect removed harness to Grom Y-harness

connect removed harness to Grom Y-harness

14.20-pin harness connects to Grom unit

20-pin harness connects to Grom unit

20-pin harness connects to Grom unit

15.Separate and test wire for +12v constant

Separate and test wire for +12v constant

Separate and test wire for +12v constant

16.After confirmation of +12v constant,use provided P-Tap to make connection,please ensure P-Tap has punctured wire and is tightly secured

 make connection with help of provided P-Tap

make connection with help of provided P-Tap

17.Fasten top cap to connect Yellow power wire

Fasten top cap to connect Yellow power wire

Fasten top cap to connect Yellow power wire

18.Insert stripped wire as far as possible

Insert stripped wire as far as possible

Insert stripped wire as far as possible

19.Gently secure cap and tug on wire to make sure it is secured

Gently secure cap and tug on wire to make sure it is secured

Gently secure cap and tug on wire to make sure it is secured

20.After making cables connection,turn on stereo and test new unit and hope that you can enjoy your new audio system

Please check the appearance and all functions of original stereo to make sure they can work well before you start to upgrade it and replace a new unit.

After that you only can start up to do your workmore wonderful by yourself.If you need to know better about new installed dvd display,you can visit the following website which has a lot of information there: http://www.seicane.com/double-din-2010-2011-mitsubishi-lancer-aftermarket-gps-radio-system-tv-tuner-cd-dvd-player-3g-wifi-pop-dvr-hd-1080p-video-backup-camera-ipod-iphone-c037.

 

Specific installation steps for 2010 2011 2012 Mazda 5 navigation system with RDS BT USB function

Original car stereo of 2010 2011 2012 Mazda 5 can be considered an old friend to you because you will meet a new friend here.After people got an aftermarket car stereo that matches Mazda 5,then learning about specific installation steps for 2010 2011 2012 Mazda 5 navigation system with RDS BT USB function may be the most troubled thing they are facing.

Some people don’t think so because they will ask professional workers to do it,however,there are a lot of people can achieve it by themselves.Isn’t it a good thing?

These people make the decision because they have known how to use the unit and act according to right installation guide.Of course it can be better if we can finish it ourselves especially for our beloved car.If not,I think you can surf the Internet to get a better understanding,for example: http://www.seicane.com/8-inch-multimedia-sat-nav-system-for-2010-2011-2012-mazda-5-with-3g-wifi-radio-tuner-dvd-bluetooth-music-usb-sd-auto-av-in-out-hd-1080p-video-aux-backup-camera-c117 .

Next are general operations for car stereo removal and installation,and you can read them patiently to rich yourself.The following content will show you right installation instructions for Mazda 5 navigation system,and remember to turn off your radio before you begin your work.

And here is an image of head unit after installation,HD radio dvd nav system with touch screen of 2010 2011 2012 Mazda 5.

head unit after installation,HD radio dvd nav system with touch screen of 2010 2011 2012 Mazda 5

head unit after installation,HD radio dvd nav system with touch screen of 2010 2011 2012 Mazda 5

2010 2011 2012 Mazda 5 factory stereo removal and new audio nav system installation:

1.Remove the panel that is in the center console

Remove the panel that is in the center console

Remove the panel that is in the center console

2.Make off the small pocket panel which is on the back of the center console behind shifter,unplug antennas between them

Make off the small pocket panel which is on the back of the center console behind shifter

Make off the small pocket panel which is on the back of the center console behind shifter

3.Remove two 8mm bolts under cup holder panel holding the back half of the center console to the front half

Remove two 8mm bolts

Remove two 8mm bolts

4.Fasten and remove the shift knob

Fasten and remove the shift knob

Fasten and remove the shift knob

5.Slip both seats forward and remove 2 Phillips screws on each side of the center consoles under the screw covers

Slip both seats forward

Slip both seats forward

remove 2 Phillips screws on each side of the center consoles under the screw covers

remove 2 Phillips screws on each side of the center consoles under the screw covers

6.Remove and shrink the panels that locate lower front sides of the center console

Remove and shrink the panels that locate lower front sides of the center console

Remove and shrink the panels that locate lower front sides of the center console

7.Remove two Phillips screws from both sides(total of 4) of the front lower half of the center console

Remove two Phillips screws from both sides

Remove two Phillips screws from both sides

8.Make off the vent panel including the hazard switch above the original radio

Make off the vent panel including the hazard switch above the original radio

Make off the vent panel including the hazard switch above the original radio

9.If you set this piece on top of the dashboard to access the screws,that will be easier ,then remove 2 screws

set this piece on top of the dashboard to access the screws

set this piece on top of the dashboard to access the screws

remove 2 screws

remove 2 screws

10.Take out 2 screws from behind shifter trim

Take out 2 screws from behind shifter trim

Take out 2 screws from behind shifter trim

11.Pull forward center console,which will help gain access to 2 screws under the climate controls

Pull forward center console

Pull forward center console

12.Make out 2 screws that are under climate controls

Make out 2 screws that are under climate controls

Make out 2 screws that are under climate controls

13.Remove harness and pull rear center console backwards

Remove harness

Remove harness

pull rear center console backwards

pull rear center console backwards

14.Press in shifter to loosen trigger and pull down shifter,make sure

to have a brake on!

Press in shifter to loosen trigger

Press in shifter to loosen trigger

pull shifter down

pull shifter down

15.Push in side prongs to fasten climate control buttons and then remove climate controls

Push in side prongs to fasten climate control buttons

Push in side prongs to fasten climate control buttons

remove climate controls

remove climate controls

16.Get out 1 screw and 1(10mm) bolt

Get out 1 screw

Get out 1 screw

 

Get out 1(10mm) bolt

Get out 1(10mm) bolt

17.Get out factory stereo to fasten clips unplug stereo connectors

Get out factory stereo to fasten clips unplug stereo connectors

Get out factory stereo to fasten clips unplug stereo connectors

Attention please:

P lease be soft and gentle to your car series especially when you are removing dashboard and CD player of head unit.In addition, be more careful when you are pluging the antennas to right positions because it is a key job.Car gps radio installation can be a self-done thing but on the condition that we take it serious and we are careful enough.

This aftermarket unit has increased some other features,such as navigation system which can show you a map on the screen,bluetooth function,and you can also watch videos when you are sure that it’s very safe to do that.

 

Detailed installation steps for 2009 Kia Sorento navigation dvd with bluetooth music

Here is the head unit after installation,navigation dvd gps bluetooth of 2009 Kia Sorento.

head unit after installation,navigation dvd gps bluetooth of 2009 Kia Sorento

head unit after installation,navigation dvd gps bluetooth of 2009 Kia Sorento

 

After you have bought a dvd radio which can match your Kia Sorento in mode and size,the installation for car stereo may be what makes us feel troubled.We may ever saw this phenomenon that someone who wants to upgrade his car stereo ask a professional worker do it.However,a lot of people choose to update the head unit by themselves under the condition that they have made clear detailed installation steps for 2009 Kia Sorento navigation dvd with bluetooth music is.

This article will show you what you need exactly if you are one of persons who have nothing to do with radio installation but want to get it by himself.Then you can patiently have a look at following instructions and take them as references.Hope that you will do a perfect job after careful installation for Kia Sorento navigation.

At first you need to figure out is that if this radio is suitable for your car.Front one which is shown in the picture is a right one,you can take it as a sample to make comparison.After that then we begin to take actions as installation guide instructed.Please remember to turn off the audio before you shut down your car,and after attention for these details,next are the removal steps for it.

2009 Kia Sorento original stereo removal and navigation system installation:

1.Use a pry tool to take out trim panels from beneath to the top of it,the same operation to the other one

Use a pry tool to take out trim panels from beneath to the top of it

Use a pry tool to take out trim panels from beneath to the top of it

the same operation to the other one

the same operation to the other one

2.Remove two screws with a special screwdriver

remove this screw and the other corresponding one  with a special screwdriver

remove this screw and the other corresponding one with a special screwdriver

3.Remove downer four screws

remove this acrew and the other corresponding one

remove this acrew and the other corresponding one

remove this lower acrew and the other corresponding one

remove this lower acrew and the other corresponding one

4.With above six screws removed,you can take dashboard down easily

take dashboard down easily

take dashboard down easily

5.This is dashboard’s inner part that connected by cables

dashboard’s inner part that connected by cables

dashboard’s inner part that connected by cables

6.Get these four screws out,include two on the other side

Get these four screws out,include two on the other side

Get these four screws out,include two on the other side

7.Remove original CD player,and then unplug the cables

Remove original CD player

Remove original CD player

8.Removal steps has been finished,next turns to installation.Install new bought player in it by correctly connecting cables and gently put it in

9.Firm four screws back to car and put dashboard back to car,too,and then go on fixing six screws

If you want to know better about new installed car head unit,then you can visit some websites to help you.For example: http://www.seicane.com/navi-system-in-2-din-hd-radio-tuner-dvd-player-specialized-for-2009-kia-sorento-with-gps-bluetooth-auto-a-v-3g-wifi-support-20-disk-virtual-cd-changer-c046.You can also contact with workers online there,they will try to help you deal with your problems.

I hope and believe that most of you can install Kia Sorento aftermarket autoradio gps yourself now. Please have a check for the unit before and after your installation,in order to make sure the security.

 

 

 

How to install 2012 Hyundai I40 aftermarket dvd support HD 1080P

Let’s have a look at following picture first:car stereo after installation,gps radio dvd player with bluetooth music USB of 2012 Hyundai I40.

car stereo after installation,gps radio dvd player with bluetooth music USB of 2012 Hyundai I40

car stereo after installation,gps radio dvd player with bluetooth music USB of 2012 Hyundai I40

It’s easy to confirm car’s model,appearance and years for these can all be gotten from the Internet,but if it’s about how to install 2012 Hyundai I40 aftermarket dvd support HD 1080P?

Many facts shows that many people,who are owners of Hyundai I40,have install dvd player into the car themselves.You may have doubts about it,but it’s true.I probably know why they can do this because these men have made the installation instructions clear which is about Hyundai I40 dvd player.

Then let’s look at above picture again,a lot of people may don’t know what a new stereo looks like,they have the desire to replace one but have no idea about what to do.It’s ok,your problems will be solved here.

First of all,you need to find a stereo from car market which looks like above one in the picture.After that,I think this unit is strange to you,there are a lot of things that you have no idea about it,so you’d better do some search works about this new unit,for example,you can visit next website to help getting more information:http://www.seicane.com/double-din-2012-hyundai-i40-gps-radio-auto-a-v-system-3g-wifi-cd-dvd-player-bluetooth-music-tv-tuner-dvr-hd-1080p-aux-steering-wheel-control-usb-sd-ipod-mp3-mp5-c172.

With adequate understanding about it,next we will begin to know what should we do step by step about Hyundai I40 radio installation.

2012 Hyundai I40 original stereo removal and dvd GPS installation:

1.Remove trim panels by prying each side of center console,you can do it with the help of a lever

Remove trim panels by prying each side of center console

Remove trim panels by prying each side of center console

pry and remove the lower part with a lever

pry and remove the lower part with a lever

2.Make 4 screws off radio trim panel

Make 4 screws off radio trim panel

Make 4 screws off radio trim panel

3.Take ac vent controls out

Take ac vent controls out

Take ac vent controls out

4.Take down 4 screws securing radio chassis to sub dash

Take down 4 screws securing radio chassis to sub dash

Take down 4 screws securing radio chassis to sub dash

5.Pull the CD player  off

Pull the CD player  off

Pull the CD player off

6.Unplug and remove radio chassis

Unplug and remove radio chassis

Unplug and remove radio chassis

Removal affairs has been finished,then you can have a comparison between yours and the one in the picture.If they look same,then you can start to mount your new car radio.

7.Connectting cables between new radio and car correctly,you can do it after you have a patient read for installation guide

8.Firm screws to their original places and reinstall trim panels to the dashboard

9.After all these,you can turn on your new head unit and have a check to see whether you have done all steps right

As long as you can act according to right instructions of installation process this won’t be dangerous work.New unit of the car has new functions including navigation system,which will bring you much convenience.

But please remember do not let the HD videos disturb your attentions when you are driving,really it can bring us convenience but not let the nav system instead of your head.

Precautions about installation and usage of the dvd radio:

1.If you haven’t prepared any electronic equipment or lack of experience, don’t install or repair the stereo for it is very dangerous

2.If you use sharp objects to operate the unit,it will damage the screen,please use a touch screen pen to do it

3.In case of the power is on,please do not do self- maintenance,service, or install the radio