The Quick Way for a 2008 2009 2010 2011-2015 Mitsubishi Lancer-ex GPS Navigation Bluetooth Car Radio Installation and Upgrade

2008 2009 2010 2011 2012-2015 Mitsubishi Lancer-ex car radio after installation

If you would like to remove your factory radio and install a new car radio, what you need to do is to find out what features you need. And if your factory radio cannot be compatible with these features you are eager to, you can think about replacing your factory radio with a new aftermarket car radio. The following is a detailed 2008 2009 2010 2011-2015 Mitsubishi Lancer-ex car radio installation instruction from Seicane. If you also own the same or similar dashboard, you can refer to this instruction.

2008 2009 2010 2011 2012-2015 Mitsubishi Lancer-ex car radio after installation

2008 2009 2010 2011 2012-2015 Mitsubishi Lancer-ex car radio after installation

Here are four tips about the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-devicesrd-400

 

2008 2009 2010 2011-2015 Mitsubishi Lancer-ex car radio installation instruction

1. Before installation, please remove any CDs from the head unit, and then disconnect the negative from your battery.

Before installation, please remove any CDs from the head unit, and then disconnect the negative from your battery

Before installation, please remove any CDs from the head unit, and then disconnect the negative from your battery

2. Remove trim pieces to access original car radio as follows.

Remove trim pieces to access original car radio as follows

Remove trim pieces to access original car radio as follows

2-1

2-1

2-2

2-2

3. Remove hazard warning accessory.

Remove hazard warning accessory

Remove hazard warning accessory

4. Disconnect Ribbon Harness and wiring loom.

5. Remove car radio fascia, please gently and carefully pull upwards from left hand corner.

Remove car radio fascia, please gently and carefully pull upwards from left hand corner

Remove car radio fascia, please gently and carefully pull upwards from left hand corner

5-1

5-1

6. Remove the four screws that are holding the original car radio in place.

Remove the four screws that are holding the original car radio in place

Remove the four screws that are holding the original car radio in place

7. Gently take out the original car radio.

Gently take out the original car radio

Gently take out the original car radio

8. Remove the original car radio’s wiring harness and antenna from the back of the car radio.

9. Remove the factory mounting brackets and install them on the new car radio.

10. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

11. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

12. Connect the Seicane car radio to your original radio’s plugs.

13. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

14. Put the new Seicane car radio into the dash.

15. Put everything into their original place. All the installation is done.

 

Wish you can learn something useful from the above installation instruction. If you encounter any difficulties and don’t know how to overcome them, you can seek for advice from your dealer or a professional. Or during the installation, you can contact your dealer, communicate with someone experienced or turn to a professional technician. Anyway, before installation, it is essential for you to select an ideal car radio for your beloved car radio. If you have no ideas, you can refer to the following link which is a remarkable 2008 2009 2010 2011-2015 Mitsubishi Lancer-ex car radio from Seicane.

https://www.seicane.com/android-2008-2015-mitsubishi-lancer-ex-hd-touchscreen-gps-navigation-radio-with-fm-bluetooth-wifi-usb-1080p-video-mirror-link-obd2-rearview-camera-s04117

With this car radio installed in your car, you will freely get access to a wide range of practical and entertainment features, such as GPS navigation function, FM/AM radio, Bluetooth hands-free phone calls, Bluetooth streaming music, AUX function, file management, etc. Thus, this all-in-one car radio from Seicane can be taken as one of the most suitable replacements for your factory radio.

Under the guidance of turn-by-turn directions and voice prompts provided by the high-accuracy 3D GPS navigation system, you can easily know your current locations and find the right way to reach your desired destinations even you are driving around an unfamiliar place. And this unit’s dual zone function enables you to listen to your favorite music while navigating.

Through Bluetooth connection between your Bluetooth-enabled mobile phone and this car radio, Bluetooth hands-free phone calls and Bluetooth streaming music are both available for you, which can give you great convenience and enjoyment.

Wish you like this unit and good luck!

How to Install and Upgrade a 2010 2011 2012 2013-2015 KIA Sportage GPS Navigation Bluetooth Head Unit Carplay Audio Radio

2010 2011 2012 2013-2015 KIA Sportage car radio after installation

If your factory radio cannot satisfy you in car since it cannot be compatible with some upgraded features, you can think about replacing your factory radio with a new aftermarket car radio. This article aims to introduce how to remove the factory radio and install the new car radio in 2010 2011 2012 2013-2015 KIA Sportage, if you own the same or similar dashboard, you can carefully refer to the following installation steps, which may help with the installation.

2010 2011 2012 2013-2015 KIA Sportage car radio after installation

2010 2011 2012 2013-2015 KIA Sportage car radio after installation

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-devicesrd-400

 

2010 2011 2012 2013-2015 KIA Sportage car radio installation instruction

1. The original car radio.

The original car radio

The original car radio

2. Uncover the screw covers on each corner and then remove the two screws with a screwdriver.

Uncover the screw covers on each corner and then remove the two screws with a screwdriver

Uncover the screw covers on each corner and then remove the two screws with a screwdriver

2-1

2-1

3. Adjust the steering wheel so as to release the panel on the left side of the radio and then remove it. Don’t forget to disconnect the connectors at the back.

Adjust the steering wheel so as to release the panel on the left side of the radio and then remove it. Don't forget to disconnect the connectors at the back

Adjust the steering wheel so as to release the panel on the left side of the radio and then remove it. Don’t forget to disconnect the connectors at the back

3-1

3-1

3-2

3-2

4. Remove the panel on the right side of the radio with a plastic removal tool.

Remove the panel on the right side of the radio with a plastic removal tool

Remove the panel on the right side of the radio with a plastic removal tool

5. Remove two screws that fixed the radio panel, then remove the panel and unplug the connector at the back.

Remove two screws that fixed the radio panel, then remove the panel and unplug the connector at the back

Remove two screws that fixed the radio panel, then remove the panel and unplug the connector at the back

5-1

5-1

6. Remove four screws that are holding the radio on the dashboard.

Remove four screws that are holding the radio on the dashboard

Remove four screws that are holding the radio on the dashboard

7. Take out the original radio and unplug the connectors at the back of it.

Take out the original radio and unplug the connectors at the back of it

Take out the original radio and unplug the connectors at the back of it

7-1

7-1

8. Check all the accessories for the new Seicane car stereo.

Check all the accessories for the new Seicane car stereo

Check all the accessories for the new Seicane car stereo

9. Connect the harnesses to the back of the new Seicane car stereo.

Connect the harnesses to the back of the new Seicane car stereo

Connect the harnesses to the back of the new Seicane car stereo

10. Connect the Seicane car stereo to your original stereo’s plugs.

11. Turn on the new Seicane car stereo to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

12. Put the new Seicane car stereo into the dash.

13. Put everything into their original place. All the installation is done.

 

Wish you can learn some skills from the above installation instruction. If you meet any difficulties and don’t know how to overcome them, please feel free to contact your dealer, communicate with someone experienced or turn to a professional technician for help. If you still think it hard to install the new car radio, you can directly go to a car radio upgrade center to have the car radio installed by a professional technician.

Anyway, before installation, please carefully pick an ideal car radio for your beloved car. Here I’d like to share a remarkable 2010 2011 2012 2013-2015 KIA Sportage car radio from Seicane with you. Fore more details, please click:

https://www.seicane.com/hd-touchscreen-radio-for-2010-2015-kia-spotage-android-with-gps-navigation-audio-system-bluetooth-music-usb-aux-wifi-1080p-tv-mirror-link-dvr-s0495

This car radio is loaded with the stable Android 6.0 operation system and a powerful quad-core CPU processor, therefore, with this car radio installed in your car, you will embrace a much smoother, faster and easier operation experience.

There are a wide range of practical and entertainment features being offered by this all-in-one car radio, mainly including 3D GPS navigation system, FM/AM radio, Bluetooth hands-free phone calls, Bluetooth streaming music, AUX function, file management, etc.

Under the wireless Bluetooth technology, through the Bluetooth connection between your Bluetooth-enabled mobile phone and this car radio, without taking your hands off the steering wheel, you are able to dial, answer, reject and mute Bluetooth hands-free phone calls as well as listen to Bluetooth streaming music from your phone.

What are you waiting for? This unit is at a competitive price now. If you like it, just add it to your shopping cart.

The Quick Steps of 2014 Honda FIT Left GPS Navigation Car Stereo Bluetooth Radio Installation

2014 Honda FIT Left car radio after installation

It is absolutely correct that an ideal car radio will be regarded as the most important part of a car since it comes with a wide range of practical and entertainment features, mainly including 3D GPS function, Bluetooth function, FM/AM radio tuner, AUX, USB or SD card connection, etc. If you plan to replace your factory radio with a new aftermarket car radio, you can go to a car radio upgrade center or ask a professional to install it in your car. And you can refer to the following    2014 Honda FIT Left car radio installation instruction from Seicane if you own the same or similar dashboard.

2014 Honda FIT Left car radio after installation

2014 Honda FIT Left car radio after installation

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2014 Honda FIT Left car radio installation instruction

1. Remove the bottom panel with a plastic removal tool and then unplug the connector behind.

Remove the bottom panel with a plastic removal tool and then unplug the connector behind

Remove the bottom panel with a plastic removal tool and then unplug the connector behind

1-1

1-1

2. Remove screws below the radio with a screwdriver.

Remove screws below the radio with a screwdriver

Remove screws below the radio with a screwdriver

3. Remove the panel on the left of the radio.

Remove the panel on the left of the radio

Remove the panel on the left of the radio

4. Release the panel one the right side of the radio.

Release the panel one the right side of the radio

Release the panel one the right side of the radio

5. Take out the original radio, please use a plastic removal tool if necessary.

Take out the original radio, please use a plastic removal tool if necessary

Take out the original radio, please use a plastic removal tool if necessary

6. Disconnect the connectors at the back of the radio.

Disconnect the connectors at the back of the radio

Disconnect the connectors at the back of the radio

7. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

8. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

9. Connect the Seicane car radio to your original radio’s plugs.

10. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

11. Put the new Seicane car radio into the dash.

12. Put everything into their original place. All the installation is done.

 

Above is the whole removal and installation process of a 2014 Honda FIT Left car radio. If you are confused with some problems and don’t know how to deal with, you can browse some professional websites for seeking advice, contact your dealer or seek help from a professional. Or you can directly go to a car radio upgrade center and arrange a professional technician to help you install the new car radio. Anyway, before installation, it is very essential for you to pick an ideal car radio. Here I would like to share a remarkable 2014 Honda FIT Left car radio from Seicane with you. For more details, please click:

https://www.seicane.com/2014-honda-fit-left-android-radio-dvd-player-gps-navigation-system-with-touchscreen-bluetooth-4g-wifi-dvr-backup-camera-dab-tpms-s168022

This powerful car radio, which is loaded with the stable Android 6.0 operation system and a high-quality quad-core CPU processor, can largely enhance its capabilities, performance and enjoyment. So it can be regarded as one of the best choices to replace your factory radio in your beloved car.

With the help of the worldwide real-time GPS navigation system of this unit, you are able to easily locate where you are and find the right way to reach any locations you would like to go to according to turn-by-turn directions and voice prompts. Besides, this unit comes with dual zone functions, so you can freely listen to your favorite music while navigating and the music will automatically switch to GPS voice.

What’s more, without keeping your hands off the steering wheel, through the Bluetooth connection between your Bluetooth-enabled mobile phone and this car radio, you are able to dial, answer, reject and mute Bluetooth hands-free phone calls as well as listen to Bluetooth streaming music from your phone music play;lists. Therefore, you can gain great convenience and enjoyment.

What are you waiting for? If you like this unit, just add it to your shopping cart right now.

How to Remove and Install a 2008 Toyota Prado USB WIFI Car Radio GPS Navigation Head Unit

2008 Toyota Prado car radio after installation

As a car owner who would like to pursue an unforgettable driving experience, you can replace your factory radio with a new aftermarket car radio, which comes with numerous comprehensive features to meet your different needs in your car. If you don’t know how to install a new car radio, you can straightly ask a professional technician to help you. The following is a 2008 Toyota Prado car radio installation guide from Seicane., which can help you gain a general understanding of the car radio installation.

2008 Toyota Prado car radio after installation

2008 Toyota Prado car radio after installation

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2008 Toyota Prado car radio installation guide

1. Gently squeeze, pull and lift away the surrounding panels on each side.

Gently squeeze, pull and lift away the surrounding panels on each side

Gently squeeze, pull and lift away the surrounding panels on each side

2. Grip gently at the bottom and lift the air conditioning vents.

Grip gently at the bottom and lift the air conditioning vents

Grip gently at the bottom and lift the air conditioning vents

3. Squeeze clips to release electrical connectors.

Squeeze clips to release electrical connectors

Squeeze clips to release electrical connectors

4. There are four screws holding the radio on the dashboard. Remove them with a screwdriver.

There are four screws holding the radio on the dashboard. Remove them with a screwdriver

There are four screws holding the radio on the dashboard. Remove them with a screwdriver

5. Gently take out the original radio.

6. Disconnect connectors and cables at the back the radio.

7. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

8. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

9. Connect the Seicane car radio to your original radio’s plugs.

10. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

11. Put the new Seicane car radio into the dash.

12. Put everything into their original place. All the installation is done.

 

Above is the whole installation instruction about a 2008 Toyota Prado car radio. If you encounter any problems and you would like to deal with on your own, you can contact your dealer, communicate with someone experienced or turn to a professional for help. To avoid making damage to either your car radio or your car, you can also directly arrange a professional technician to help you install the new car radio. To help you select an ideal car radio for your beloved car, here I would like to share an amazing 2008 Toyota Prado car radio from Seicane with you. For more details, please click:

https://www.seicane.com/android-2008-toyota-prado-radio-gps-navigation-system-with-bluetooth-hd-touchscreen-wifi-1080p-dvr-mirror-link-rearview-s0456

This car radio will provide you with a wonderful driving experience since it is compatible with a wide range of practical and entertainment features.

Under the guidance of the turn-by-turn directions and voice prompts provided by the high-end 3D GPS navigation system, even you are driving around an unfamiliar city, you can easily locate where you are and accurately navigate to any locations you would like to go to. And this unit also comes with dual zone function, which enables you to listen to your favorite music while navigating.

Besides, through the wireless Bluetooth connection between your Bluetooth-enabled mobile phone and this car radio, you are able to freely dial, answer, reject and mute Bluetooth hands-free phone calls as well as listen to Bluetooth streaming music without taking your hands off the steering wheel control.

If you like this car radio, please don’t hesitate to add it to your shopping cart. Good luck!

How to Quick Install and Upgrade a 2007 2008 2009 2010-2013 Honda Fit Bluetooth 3G WIFI GPS Navigation Car Radio Unit

2007 2008 2009 2010-2013 Honda Fit Car Stereo after installation

If you are not satisfied with your factory radio since it cannot be compatible with some modern or upgraded features, it is suggested that you can replace your factory radio with a new aftermarket car radio. If you wonder how to install a 2007 2008 2009 2010-2013 Honda Fit car radio, then you can carefully read the following installation instruction on a 2007 2008 2009 2010-2013 Honda Fit car radio. Wish it is helpful for you.

2007 2008 2009 2010-2013 Honda Fit Car Stereo after installation

2007 2008 2009 2010-2013 Honda Fit Car Stereo after installation

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2007 2008 2009 2010-2013 Honda Fit car radio installation instruction

1. Open the glove box at first.

Open the glove box at first

Open the glove box at first

2. Remove the four screws of gloves box as these pictures show.

Remove the four screws of gloves box as these pictures show

Remove the four screws of gloves box as these pictures show

2-1

2-1

2-2

2-2

2-3

2-3

3. Unscrew the two bolts under the radio.

Unscrew the two bolts under the radio

Unscrew the two bolts under the radio

3-1

3-1

4. Take out the original car radio.

Take out the original car radio

Take out the original car radio

5. Remove the original car radio.

Remove the original car radio

Remove the original car radio

6. Disconnect all connectors at the back of the original car radio.

Disconnect all connectors at the back of the original car radio

Disconnect all connectors at the back of the original car radio

7. Remove screws of air condition as these pictures show.

Remove screws of air condition as these pictures show

Remove screws of air condition as these pictures show

7-1

7-1

7-2

7-2

7-3

7-3

8. Pull out the air outlet of air condition.

Pull out the air outlet of air condition

Pull out the air outlet of air condition

9. Remove the hazard warning switch light.

Remove the hazard warning switch light

Remove the hazard warning switch light

10. Install the air outlet with the unit.

11. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

12. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

13. Connect the Seicane car radio to your original car radio’s plugs.

14. Turn on the new Seicane radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

15. Put the new Seicane radio into the dash.

16. Put everything into their original place. All the installation is done.

 

If you have any doubts, please feel free to consult your dealer, communicate with someone experienced or turn to a professional for help. If you still think it hard to finish the whole installation process, you’d better arrange a professional technician to help you install the new car radio straightly. Besides, if you don’t know how to select a suitable car stereo for your car, I’d like to recommend an amazing 2007 2008 2009 2010-2013 Honda Fit car radio from Seicane to you. For more details, please click:

https://www.seicane.com/2007-2008-2009-2013-honda-fit-android-hd-touchscreen-gps-navigation-system-with-bluetooth-wifi-mirror-link-steering-wheel-control-s0402

This powerful car radio is running on the stable Android 6.1 operation system and high-quality quad-core CPU processor.

Even though you are not good at identifying directions, the high-accuracy 3D GPS navigation system is specially built in to offer you some help. With the help of the worldwide real-time navigation, you can get access to features like current location, 3D street view, landmark building display, turn-by-turn voice directions, etc. So you can be accurately guided to arrive at your desired destinations.

Additionally, under the wireless Bluetooth technology, without taking your hands off the steering wheel, both Bluetooth hands-free phone calls and Bluetooth streaming music are available as long as you pair your Bluetooth-enabled mobile phone with this unit.

Wish you like this multifunctional car radio and good luck to you!

Skillfully Install and Upgrade a 2004 2005 2006 2007-2010 Toyota Sienna GPS Navigation Bluetooth Car Radio Audio System

2004 2005 2006 2007-2010 Toyota Sienna Car Radio after installation

Are you searching for the methods to upgrade your car’s capacities? If yes, it will be a great idea for you to remove your outdated factory radio and install a brand new multifunctional car radio. And with some related installation experience and the guidance of a correct installation instruction, it will be much easy for you to have a general understanding of the new car radio installation process. The following is a 2004 2005 2006 2007-2010 Toyota Sienna car radio installation instruction. If you happen to own the same car model, then you can take this instruction as a reference.

2004 2005 2006 2007-2010 Toyota Sienna Car Radio after installation

2004 2005 2006 2007-2010 Toyota Sienna Car Radio after installation

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2004 2005 2006 2007-2010 Toyota Sienna car radio installation instruction

1. The original car radio for 2004-2010 Toyota Sienna.

The original car radio for 2004-2010 Toyota Sienna

The original car radio for 2004-2010 Toyota Sienna

2. Use a flat-head screwdriver or a flat pry tool to pry up the vertical panels of the right and left side of the original car radio and climate control system.

Use a flat-head screwdriver or a flat pry tool to pry up the vertical panels of the right and left side of the original car radio and climate control system

Use a flat-head screwdriver or a flat pry tool to pry up the vertical panels of the right and left side of the original car radio and climate control system

3. Disconnect the wiring from the side panels. There are two wiring connectors on the left panel and only one connector on the right panel. Please carefully press the tab to release the connectors.

Disconnect the wiring from the side panels. There are two wiring connectors on the left panel and only one connector on the right panel. Please carefully press the tab to release the connectors

Disconnect the wiring from the side panels. There are two wiring connectors on the left panel and only one connector on the right panel. Please carefully press the tab to release the connectors

3-1

3-1

4. Remove the center channel speaker grill panel above the car radio. Please use a pry tool or a flat head screwdriver to pry up the top (center channel speaker) panel above the car radio and then remove it.

Remove the center channel speaker grill panel above the car radio. Please use a pry tool or a flat head screwdriver to pry up the top (center channel speaker) panel above the car radio and then remove it

Remove the center channel speaker grill panel above the car radio. Please use a pry tool or a flat head screwdriver to pry up the top (center channel speaker) panel above the car radio and then remove it

4-1

4-1

5. Remove the center speaker. There are two 10mm hex head nuts securing the center speaker, so you need to use a 10-mm Hollow-Shank nut screwdriver to remove these two bolts.

Remove the center speaker. There are two 10mm hex head nuts securing the center speaker, so you need to use a 10-mm Hollow-Shank nut screwdriver to remove these two bolts

Remove the center speaker. There are two 10mm hex head nuts securing the center speaker, so you need to use a 10-mm Hollow-Shank nut screwdriver to remove these two bolts

6. Disconnect the speaker wiring harness. Please press the tab down so as to release the wiring connector, and then set the speaker and bolts aside.

Disconnect the speaker wiring harness. Please press the tab down so as to release the wiring connector, and then set the speaker and bolts aside

Disconnect the speaker wiring harness. Please press the tab down so as to release the wiring connector, and then set the speaker and bolts aside

7. Remove the 4 10mm hex head nuts from the car radio. There are 4 bolts holding the car radio in the dash (2 on each side). Please use a screwdriver to remove these four bolts.

Remove the 4 10mm hex head nuts from the car radio. There are 4 bolts holding the car radio in the dash (2 on each side). Please use a screwdriver to remove these four bolts

Remove the 4 10mm hex head nuts from the car radio. There are 4 bolts holding the car radio in the dash (2 on each side). Please use a screwdriver to remove these four bolts

7-1

7-1

8. Gently pull the original car radio out of the dash and then disconnect the wiring from the original car radio. Then put the original car radio aside.

Gently pull the original car radio out of the dash and then disconnect the wiring from the original car radio. Then put the original car radio aside

Gently pull the original car radio out of the dash and then disconnect the wiring from the original car radio. Then put the original car radio aside

8-1

8-1

9. If necessary, please remove the left and right radio mounting brackets to install on the new Seicane car radio.

If necessary, please remove the left and right radio mounting brackets to install on the new Seicane car radio

If necessary, please remove the left and right radio mounting brackets to install on the new Seicane car radio

10. Check all the accessories for the new Seicane car radio.

11. Connect the harnesses to the back of the new Seicane car radio.

12. Connect the Seicane car radio to your original car radio’s plugs.

Connect the Seicane car radio to your original car radio's plugs

Connect the Seicane car radio to your original car radio’s plugs

13. Gently place the new Seicane car radio into the opening of the dash and test it.

14. Re-seat the stereo in the dash and reinstall the 4 bolts.

15. Carefully reconnect the center speaker and reinstall the 2 bolts.

Carefully reconnect the center speaker and reinstall the 2 bolts

Carefully reconnect the center speaker and reinstall the 2 bolts

16. Carefully reinstall top center channel speaker grill panel.

Carefully reinstall top center channel speaker grill panel

Carefully reinstall top center channel speaker grill panel

17. Reconnect all the electrical connectors and then reinstall the left and right side panels.

 

Don’t worry if you cannot fully understand the above removal and installation steps. Under this circumstance, you can contact your dealer, communicate with someone experienced or turn to a professional for help. If you are afraid of making damage to either your car radio or your car, you can also ask a professional technician to help you install the new car radio. Anyway, it is very essential for you to pick an ideal car radio for your beloved car radio. If you don’t know which kind of car radio can fit your car, here I would like to share a remarkable 2004 2005 2006 2007-2010 Toyota Sienna car radio from Seicane with you. For more information, please click:

https://www.seicane.com/android-hd-touchscrenn-2-din-radio-head-unit-for-2001-2006-acura-mdx-gps-navigation-system-bluetooth-phone-wifi-support-1080p-video-usb-steering-wheel-control-backup-camera-s69137

This powerful car radio is running with the intelligent Android 6.0 operation system and a high-quality quad-core CPU processor to greatly enhance the processing ability.

Even though you are not good at identifying directions, with the assistance of the turn-by-turn directions and voice prompts provided by the 3D GPS navigation system of high precision, you can not only quickly know your current locations but also know the correct way to get to your desired destinations. And while navigating, you can also listen to your favorite music.

Additionally, under the wireless Bluetooth technology, you can make this car radio connect to your Bluetooth-enabled mobile so that you can freely get access to both Bluetooth hands-free phone calls as well as Bluetooth streaming music without taking your hands off the steering wheel. In a word, with this car radio installed in your car, your in-car life will definitely be improved to a new level.

If you like this car radio, just don’t hesitate to add it to your shopping cart right now!

How to Upgrade a 2011 2012 2013 2014 BMW X5 E70 /X6 E71 CIC Car Stereo with DVD player GPS Navigation System

2011 2012 2013 2014 BMW X5 E70 X6 E71 CIC Car Stereo after installation

If you are not satisfied with your factory radio, it is suggested that you should think about removing your factory radio and installing anew aftermarket car radio. To achieve the whole removal and installation process, it is helpful for you to refer to a detailed installation instruction. The following is a 2011 2012 2013 2014 BMW X5 E70 /X6 E71 CIC car radio installation instruction from Seicane, which can be taken as your reference.

2011 2012 2013 2014 BMW X5 E70 X6 E71 CIC Car Stereo after installation

2011 2012 2013 2014 BMW X5 E70 X6 E71 CIC Car Stereo after installation

Some tips before the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2011 2012 2013 2014 BMW X5 E70 /X6 E71 CIC car radio installation instruction

1. Press the button that indicated so as to open the glove box.

Press the button that indicated so as to open the glove box

Press the button that indicated so as to open the glove box

1-1

1-1

2. Use a pry tool to pry loose the air vent dash trim.

Use a pry tool to pry loose the air vent dash trim

Use a pry tool to pry loose the air vent dash trim

2-1

2-1

3. Pull out the air-conditioning vent and disconnect the plugs connected behind it.

Pull out the air-conditioning vent and disconnect the plugs connected behind it

Pull out the air-conditioning vent and disconnect the plugs connected behind it

3-1

3-1

4. Then you are going to come the side and pull out the one switch for the actual glove box compartment.

Then you are going to come the side and pull out the one switch for the actual glove box compartment

Then you are going to come the side and pull out the one switch for the actual glove box compartment

5. Use a screwdriver to remove the two screws that fix the original car radio dash trim.

Use a screwdriver to remove the two screws that fix the original car radio dash trim

Use a screwdriver to remove the two screws that fix the original car radio dash trim

5-1

5-1

6. Remove two clips that are behind this radio face.

Remove two clips that are behind this radio face

Remove two clips that are behind this radio face

6-1

6-1

7. Remove four screws that fix the original car radio and pull it out from the dash. Then unplug the connectors and wires behind the car radio.

Remove four screws that fix the original car radio and pull it out from the dash. Then unplug the connectors and wires behind the car radio

Remove four screws that fix the original car radio and pull it out from the dash. Then unplug the connectors and wires behind the car radio

8. Unscrew the screws that fix the original display screen and then remove the screen.

Unscrew the screws that fix the original display screen and then remove the screen

Unscrew the screws that fix the original display screen and then remove the screen

9. Disconnect the connectors at the back of the screen.

Disconnect the connectors at the back of the screen

Disconnect the connectors at the back of the screen

10. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

11. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

12. Connect the Seicane car radio to your original radio’s plugs.

13. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

14. Put the new Seicane car radio into the dash.

15. Put everything into their original place. All the installation is done.

 

Don’t worry if you encounter any problems before or during the installation. To fully solve the problems, you can try to contact your dealer, communicate with someone experienced or turn to a professional for help. Or if you are afraid of making damage to either your car radio or your car, you can directly arrange a professional technician to help you install the new car radio. Anyway, before installation, it is very vital for you to select an ideal car radio for your car. If you don’t know which kind of car radio can fit your car, you can refer to the following link which is a remarkable 2011 2012 2013 2014 BMW X5 E70 /X6 E71 CIC car radio from Seicane.

https://www.seicane.com/android-hd-touchscreen-car-stereo-radio-for-2011-2012-2013-2014-bmw-x5-e70-x6-e71-cic-head-unit-gps-navigation-bluetooth-phone-music-wifi-support-usb-steering-wheel-control-backup-camera-s028225

There is no doubt that with this great car radio installed in your car, your driving experience will be taken up a notch naturally. This car radio comes with a wide range of practical and entertainment features, which meets almost all your needs in car.

With the assistance of the worldwide real-time GPS navigation system of high precision, you are allowed to easily locate where you are and accurately find the right way to get to reach any locations you would like to go to according to the turn-by-turn directions and voice prompts. And this car radio’s dual zone function enables you to listen to your favorite music while navigating, and the music will automatically switch to GPS voice.

Additionally, through the Bluetooth connection between your Bluetooth-enabled mobile phone and this car radio, without taking your hands off the steering wheel for a long time, you are enabled to dial, receive, reject and mute Bluetooth hands-free phone calls as well as listen to Bluetooth streaming music from your phone music playlist.

Wish you like this car radio. Good luck!

 

 

 

A Detailed Installation Instruction on a 1998 1999 2000 2001-2006 BMW E53 X5 Car Radio Support Bluetooth GPS Navigation

1998 1999 2000 2001-2006 BMW E53 X5 car radio after installation

If you would like to effectively improve your driving experience, it is a wise choice for you to replace your factory radio with a new aftermarket car radio. And to reduce some budget on upgrading, you can try to deal with the installation all on your own. The following is a 1998 1999 2000 2001-2006 BMW E53 X5 car radio installation instruction. If you own the same or similar dashboard, you can take this instruction as a reference.

1998 1999 2000 2001-2006 BMW E53 X5 car radio after installation

1998 1999 2000 2001-2006 BMW E53 X5 car radio after installation

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts (Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professionals.

7. For your convenience, here are the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-devicesrd-400

 

1998 1999 2000 2001-2006 BMW E53 X5 car radio installation instruction

1. Original Dash.

Original Dash

Original Dash

2. Remove the CD decorative frame with a tool.

Remove the CD decorative frame with a tool

Remove the CD decorative frame with a tool

3. Remove the four screws with a screwdrivers.

Remove the four screws with a screwdrivers

Remove the four screws with a screwdrivers

4. Withstand the bottom(arrows) with a tool.

Withstand the bottom(arrows) with a tool

Withstand the bottom(arrows) with a tool

5. Remove the conditioning air outlet.

Remove the conditioning air outlet

Remove the conditioning air outlet

6. Stick the paper well.

Stick the paper well

Stick the paper well

7. Cut along the RED LINE.

Cut along the RED LINE

Cut along the RED LINE

8. After Cutting.

After Cutting

After Cutting

9. Remove the original Blue Plug and White Plug.

Remove the original Blue Plug and White Plug

Remove the original Blue Plug and White Plug

10. Find out the AUX Jack(3Pins).

Find out the AUX Jack(3Pins)

Find out the AUX Jack(3Pins)

11. Take out the device and locked well the holder in the base with a PA2.6*8 screw.

Take out the device and locked well the holder in the base with a PA2.6*8 screw

Take out the device and locked well the holder in the base with a PA2.6*8 screw

12. Plug well the Power Harness/ USB Cable/GPS Antenna.

Plug well the Power Harness/ USB Cable/GPS Antenna

Plug well the Power Harness/ USB Cable/GPS Antenna

13. Install well the monitor in the dashboard and locked well.

Install well the monitor in the dashboard and locked well

Install well the monitor in the dashboard and locked well

14. Fixed well the holder in the bottom of the air conditioning with TM 5.0X14MM screws.

Fixed well the holder in the bottom of the air conditioning with TM 5.0X14MM screws

Fixed well the holder in the bottom of the air conditioning with TM 5.0X14MM screws

15. Plug the original AUX with Android AUX Jack.

Plug the original AUX with Android AUX Jack

Plug the original AUX with Android AUX Jack

16. Connect Android Black Plug into Original Blue Socket.

Connect Android Black Plug into Original Blue Socket

Connect Android Black Plug into Original Blue Socket

17. Connect original Blue Plug into Android Black Socket.

Connect original Blue Plug into Android Black Socket

Connect original Blue Plug into Android Black Socket

18. Full test all the functions.

Full test all the functions

Full test all the functions

19. Switch to “AUX MODE”, Android will have sound from original speakers.

Switch to “AUX MODE”, Android will have sound from original speakers

Switch to “AUX MODE”, Android will have sound from original speakers

20. Installation Effect.

Installation Effect

Installation Effect

 

Above is the whole removal and installation steps about a 1998 1999 2000 2001-2006 BMW E53 X5 car radio. If you meet any problems you cannot deal with independently, it is suggested that you should contact your dealer, communicate with someone experienced or turn to a professional for help. If you are afraid of making damage to either your car radio or your car, you can refer to the following link which is a remarkable 1998 1999 2000 2001-2006 BMW E53 X5 car radio from Seicane. For more details, please click:

https://www.seicane.com/android-1998-2006-bmw-e53-x5-car-stereo-radio-head-unit-gps-navigation-system-bluetooth-support-usb-wifi-rearview-camera-steering-wheel-control-s028205

If you get this remarkable car radio installed in your car, you will be able to get access to a wide range of practical and entertainment features, so that you will get a wonderful driving experience.

With the assistance of the worldwide real-time GPS navigation function of this unit, you can easily locate where you are currently and gain the optimal route option to get to your desired destinations according to the turn-by-turn directions and voice prompts. And what you cannot ignore is that this unit comes with dual zone function,

Additionally, without keeping your hands off the steering wheel control, you are able to dial, answer, reject and mute Bluetooth hands-free phone calls for convenience as well as listen to Bluetooth streaming music from your phone music playlist for enjoyment.

What are you waiting for? If you like this unit, just add it to your shopping cart.

Top Effectively Upgrade and Install a 2011 2012 2013 2014-2016 BMW 1 Series F20/F21 (LHD) GPS Sat Nav Bluetooth Mirror Link Car Stereo

2011 2012 2013 2014-2016 BMW 1 Series F20F21 (LHD) car radio after installation

Do you have a car and have a plan to upgrade your factory radio by installing a brand new one? If your answer is “yes”, whether you are going to finish the installation by yourself or not, it is essential for you to find a correct installation guide to help you have a better understanding of the installation. Here I’d like to introduce a 2011 2012 2013 2014-2016 BMW 1 Series F20/F21 (LHD) car radio installation instruction to you. Wish it can help you to some extent.

2011 2012 2013 2014-2016 BMW 1 Series F20F21 (LHD) car radio after installation

2011 2012 2013 2014-2016 BMW 1 Series F20F21 (LHD) car radio after installation

Some tips before the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2011 2012 2013 2014-2016 BMW 1 Series F20/F21 (LHD) car radio installation instruction

1. The original car radio.

The original car radio

The original car radio

2. Use a pry tool to loose the air vent and then remove the air vent.

Use a pry tool to loose the air vent and then remove the air vent

Use a pry tool to loose the air vent and then remove the air vent

3. Unplug the connectors at the back of the air vent.

Unplug the connectors at the back of the air vent

Unplug the connectors at the back of the air vent

4. Use a screwdriver to remove the screws that fix the radio panel.

Use a screwdriver to remove the screws that fix the radio panel

Use a screwdriver to remove the screws that fix the radio panel

5. Take out the panel.

Take out the panel

Take out the panel

6. Disconnect the connectors at the back of the panel.

Disconnect the connectors at the back of the panel

Disconnect the connectors at the back of the panel

7. Use a screwdriver to remove the screws of the radio and then pull out the original car radio.

Use a screwdriver to remove the screws of the radio and then pull out the original car radio

Use a screwdriver to remove the screws of the radio and then pull out the original car radio

8. Unplug the connectors or cables at the back of the car radio.

Unplug the connectors or cables at the back of the car radio

Unplug the connectors or cables at the back of the car radio

9. Remove the two screws that fix the display and then remove the display.

Remove the two screws that fix the display and then remove the display

Remove the two screws that fix the display and then remove the display

10. Check all the accessories for the new Seicane car radio.

11. Connect the harnesses to the back of the new Seicane car radio.

12. Connect the Seicane car radio to your original radio’s plugs.

13. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

14. Put the new Seicane car radio into the dash.

15. Put everything into their original place. All the installation is done.

 

Don’t worry if you encounter any problems and don’t know how to deal with. Under this circumstance, you can consult your dealer, someone experienced or turn to a professional for help. Or for avoiding damage to either your car radio or your car, you can directly arrange a professional technician to help you install the new car radio.

Anyway, before installation, it is crucial for you to select an ideal car radio. If you don’t know which kind of car radios can fit your car, you can refer to a 2011 2012 2013 2014-2016 BMW 1 Series F20/F21 (LHD) car radio from Seicane. For more details, please click:

https://www.seicane.com/hd-touchscreen-radio-android-head-unit-for-2011-2016-bmw-1-series-f20-f21-car-stereo-gps-navigation-system-bluetooth-phone-wifi-support-mirror-link-1080p-video-obdii-dvr-steering-wheel-control-usb-s028211

With this car radio installed in your car, you can get access to a lot of practical and entertainment features, such as FM/AM radio tuner, Bluetooth hands-free phone calls, Bluetooth streaming music, AUX function, file management, SD card or USB connection. Therefore, almost all your needs in car can be met thanks to these features.

With the assistance of the high-end 3D GPS navigation of high accuracy, you can easily know your current locations and navigate to any locations you would like to go to under the guidance of the turn-by-turn directions and voice prompts. And thanks to this unit’s dual zone function, you are able to enjoy your favorite music while navigating, which won’t have any negative influence on GPS function.

Additionally, the built-in wireless Bluetooth module enables you to pair your Bluetooth-enabled mobile phone with this car radio. By doing so, you can dial, answer, reject and mute Bluetooth hands-free phone calls as well as Bluetooth streaming music. Therefore, you can gain a lot of convenience and enjoyment during driving.

Wish you like this car radio and good luck to you.

Top Install and upgrade tutorial for a 2012 Honda Civic GPS Navigation Bluetooth Car Radio Stereo Audio system

An ideal car radio should be compatible with both practical and entertainment features, so it can bring you great convenience and entertainment. If you think your car radio’s functions are too limited, you might as well consider replacing your factory radio with a brand new car radio. This article aims to introduce the installation steps of a 2012 Honda Civic car radio from Seicane. If you own the same or similar dashboard, you can refer to these steps carefully.

2012 Honda Civic car radio after installation

2012 Honda Civic car radio after installation

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2012 Honda civic (LHD) car radio installation instruction

1. Remove the automotive oil table top panel with plastic knife.

Remove the automotive oil table top panel with plastic knife

Remove the automotive oil table top panel with plastic knife

2. Remove the screws under the original car CD.

Remove the screws under the original car CD

Remove the screws under the original car CD

3. Take the original radio out of the dash.

Take the original radio out of the dash

Take the original radio out of the dash

4. Pull the plugs at the back of the original radio.

Pull the plugs at the back of the original radio

Pull the plugs at the back of the original radio

5. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio

Check all the accessories for the new Seicane car radio

6. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio

Connect the harnesses to the back of the new Seicane car radio

7. Connect the Seicane car radio to your original car radio’s plugs.

8. Put the new Seicane car radio into the dash.

9. Turn on the new Seicane car radio and check whether the unit is working properly. If not, please check whether all the cables are connected correctly.

10. Install screws and the panel, and put everything into their original place.

 

So now do you have a general understanding of the whole removal and installation steps of a car radio? If you still think it hard to install such a car radio by yourself, it is sincerely suggested that you should seek help from your dealer, someone experienced or a professional. Or you can straightly go to a car radio upgrade center and make the new car radio installed by a professional technician. Additionally, if you are still looking for a suitable car radio but have no ideas, here I would like to share a remarkable 2012 Honda Civic car radio from Seicane with you. For more details, please click:

https://www.seicane.com/seicane-s128201-android-radio-gps-car-audio-system-for-2012-honda-civic-with-cd-dvd-player-bluetooth-music-3g-wifi-mirror-link-obd2-hd-multi-touch-capacitive-screen

This car radio is running on the stable Android 6.0 operation system and a powerful quad-core CPU processor to enhance its capabilities and performance.

With this car radio installed in your car, you will be able to get access to a lot of practical and entertainment features, which can greatly improve your in-car life.

As for the 3D GPS navigation function, what you cannot ignore is that with its help, you can easily know your current locations and accurately find the right way to arrive at any locations you would like to go to according to turn-by-turn directions and voice prompts. And this unit comes with dual zone function, which allows you to listen to your favorite music while navigating.

Through the wireless Bluetooth connection between your Bluetooth-enabled mobile phone and this car radio, you can freely dial, answer, reject and mute Bluetooth hands-free phone calls as well as Bluetooth streaming music from your phone.

If you like this unit, just don’t hesitate to add it to your shopping cart. Good luck!